HP DL320 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide - Page 121

System Configuration Switch (SW1), running the ROM-Based Setup Utility RBSU.

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

LEDs, Switches, and Jumpers When adding or removing a component or changing a security feature, the server must be reconfigured to recognize these changes. If the system configuration is incorrect, the server may not work properly, and you may receive error messages on the screen. IMPORTANT: Reserved switches are provided for use by authorized service providers only and should not be changed from the indicated default settings. Refer to Figure E-3 and Table E-3 for location on the system board of the System Configuration Switch. The following subsections provide reference information about setting the system board switches and jumpers, which is part of the reconfiguration process, along with running the ROM-Based Setup Utility (RBSU). System Configuration Switch (SW1) The system configuration switch (SW1) is an eight-position switch used for system configuration. Refer to the labels attached to the inside of the server access panel for the proper system configuration switch settings. The following table shows the shipping configuration of SW1. E-8 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
LEDs, Switches, and Jumpers
When adding or removing a component or changing a security feature, the server
must be reconfigured to recognize these changes. If the system configuration is
incorrect, the server may not work properly, and you may receive error messages on
the screen.
IMPORTANT:
Reserved switches are provided for use by authorized service providers only
and should not be changed from the indicated default settings.
Refer to Figure E-3 and Table E-3 for location on the system board of the System
Configuration Switch.
The following subsections provide reference information about setting the system
board switches and jumpers, which is part of the reconfiguration process, along with
running the ROM-Based Setup Utility (RBSU).
System Configuration Switch (SW1)
The system configuration switch (SW1) is an eight-position switch used for system
configuration. Refer to the labels attached to the inside of the server access panel for
the proper system configuration switch settings. The following table shows the
shipping configuration of SW1.
E-8
HP ProLiant DL320 Generation 2 Server Setup and Installation Guide