HP DL320 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide - Page 41

Remove the PCI riser board assembly. Refer to the Removing the PCI Riser

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Installing Hardware Options To install an ATA hard drive: 1. Access internal server components. Refer to the "Accessing Internal Server Components" section earlier in this chapter. 2. Set the jumpers on the ATA hard drive to Cable-Select mode. Refer to the documentation included with the hard drive option kit. CAUTION: Whenever installing hardware or performing maintenance procedures requiring access to internal components, it is recommended that all server data be backed up to avoid loss. 3. Remove the PCI riser board assembly. Refer to the "Removing the PCI Riser Board Assembly" section earlier in this chapter. 4. Remove the center wall. Use the following procedure to remove the center wall: a. Disconnect the center wall fan cables from the fan connectors on the system board. Figure 3-15: Disconnecting the center wall fan cables 3-20 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Installing Hardware Options
To install an ATA hard drive:
1.
Access internal server components. Refer to the “Accessing Internal Server
Components” section earlier in this chapter.
2.
Set the jumpers on the ATA hard drive to Cable-Select mode. Refer to the
documentation included with the hard drive option kit.
CAUTION:
Whenever installing hardware or performing maintenance
procedures requiring access to internal components, it is recommended that all
server data be backed up to avoid loss.
3.
Remove the PCI riser board assembly. Refer to the “Removing the PCI Riser
Board Assembly” section earlier in this chapter.
4.
Remove the center wall. Use the following procedure to remove the center wall:
a.
Disconnect the center wall fan cables from the fan connectors on the system
board.
Figure 3-15: Disconnecting the center wall fan cables
3-20
HP ProLiant DL320 Generation 2 Server Setup and Installation Guide