HP DL320 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide - Page 40

Set the jumpers on both ATA drives to Cable-Select mode. Doing so enables - proliant dl320s server heat

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Installing Hardware Options When installing ATA hard drives in the server, observe the following general guidelines: • Do not add more than two ATA devices per channel. • Always populate hard drive bays starting with the lowest ATA device number. • Configure ATA hard drives through the Cable-Select mode. • Set the jumpers on both ATA drives to Cable-Select mode. Doing so enables the ATA cable to set a unique address, such as Device 0 or Device 1, for each hard drive. CAUTION: Installing unsupported hard drives may damage the system by consuming power and generating heat in excess of the server's operating tolerance. This condition may result in a loss of system and/or data integrity. CAUTION: When supporting a mixed environment of ATA drives and SCSI drives in the server, the ATA drive must be the boot device. ATA hard drives installed in the server appear as Devices 0 and 1, from left to right when viewed from the front of the server. Refer to Figure 3-21. HP ProLiant DL320 Generation 2 Server Setup and Installation Guide 3-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Installing Hardware Options
When installing ATA hard drives in the server, observe the following general
guidelines:
•
•
•
•
Do not add more than two ATA devices per channel.
Always populate hard drive bays starting with the lowest ATA device number.
Configure ATA hard drives through the Cable-Select mode.
Set the jumpers on both ATA drives to Cable-Select mode. Doing so enables the
ATA cable to set a unique address, such as Device 0 or Device 1, for each hard
drive.
CAUTION:
Installing unsupported hard drives may damage the system by
consuming power and generating heat in excess of the server’s operating tolerance.
This condition may result in a loss of system and/or data integrity.
CAUTION:
When supporting a mixed environment of ATA drives and SCSI drives in
the server, the ATA drive must be the boot device.
ATA hard drives installed in the server appear as Devices 0 and 1, from left to right
when viewed from the front of the server. Refer to Figure 3-21.
HP ProLiant DL320 Generation 2 Server Setup and Installation Guide
3-19