HP DL320 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide - Page 37

previously removed, go to step 2., Remove the shipping/ejector key from the inside of the server or - dl320s storage server

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Installing Hardware Options CAUTION: Do not operate the server without a bezel blank or either a CD-ROM/diskette or DVD-ROM/diskette drive assembly installed. Improper cooling can damage the system. CAUTION: Always install the shipping/ejector key in its storage location inside the chassis before shipping the server. Failure to do so can result in damage to the CD-ROM/diskette or DVD-ROM/diskette drive assembly. To install the CD-ROM/diskette or DVD-ROM/diskette drive assembly: 1. Remove the shipping/ejector key from the inside of the server or, if the key was previously removed, go to step 2. NOTE: The shipping/ejector key secures either the CD-ROM/diskette or DVDROM/diskette drive assembly or the bezel blank during shipping. It is also used to eject the assembly or the blank. a. Access internal server components. Refer to the "Accessing Internal Server Components" section earlier in this chapter. b. Remove the shipping/ejector key from its storage location. Figure 3-12: Removing the shipping/ejector key 3-16 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Installing Hardware Options
CAUTION:
Do not operate the server without a bezel blank or either a
CD-ROM/diskette or DVD-ROM/diskette drive assembly installed. Improper cooling
can damage the system.
CAUTION:
Always install the shipping/ejector key in its storage location inside the
chassis before shipping the server. Failure to do so can result in damage to the
CD-ROM/diskette or DVD-ROM/diskette drive assembly.
To install the CD-ROM/diskette or DVD-ROM/diskette drive assembly:
1.
Remove the shipping/ejector key from the inside of the server or, if the key was
previously removed, go to step 2.
NOTE:
The shipping/ejector key secures either the CD-ROM/diskette or DVD-
ROM/diskette drive assembly or the bezel blank during shipping. It is also used to eject
the assembly or the blank.
a.
Access internal server components. Refer to the “Accessing Internal Server
Components” section earlier in this chapter.
b.
Remove the shipping/ejector key from its storage location.
Figure 3-12: Removing the shipping/ejector key
3-16
HP ProLiant DL320 Generation 2 Server Setup and Installation Guide