HP DL320 HP ProLiant DL320 Generation 2 Server Setup and Installation Guide - Page 28

Installing Additional Memory, DDR SDRAM Dual Inline Memory Modules DIMMs installed in four sockets - proliant fan speed

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Installing Hardware Options Table 3-1: System Board Connectors and Components continued Location Component Location Component 13 CD-ROM/diskette or DVD/diskette connector 17 Processor socket (populated) 14 ATA controller (primary) 18 Remote Insight Lights-Out Edition II connector 15 Center wall fan connectors 19 NMI debug button 16 Processor power connector 20 DIMM sockets (1-4) Installing Additional Memory Server memory can be expanded by installing Double Data Rate Synchronous DRAM (DDR SDRAM). The system supports up to four PC2100 ECC registered DDR SDRAM Dual Inline Memory Modules (DIMMs) installed in four sockets on the system board. Memory can be added one module at a time. Refer to Figure 3-4 and to Table 3-1 for DIMM slot location and socket numbers. This information is also available on the hood label. The server memory can be expanded to 4 GB. In the maximum memory configuration, all four DIMM sockets are populated with 1-GB, PC2100 ECC registered DDR SDRAM DIMMs. Observe the following guidelines when installing additional memory: • DIMMs installed in the server must be PC2100 registered DDR SDRAM, 2.5 V, 64 bits wide, and ECC. • All DIMMs installed must be the same speed. Do not install DIMM modules supporting different speeds, for example, 266 MHz and 200 MHz. • Install the DIMMs in descending sequential order, starting with DIMM socket 4. • Use only HP recommended DIMMs. DIMMs from other sources can adversely affect data integrity • Use only the 3.05 cm (1.2 inch) DIMMs. HP ProLiant DL320 Generation 2 Server Setup and Installation Guide 3-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Installing Hardware Options
Table 3-1:
System Board Connectors and Components
continued
Location
Component
Location
Component
13
CD-ROM/diskette or
DVD/diskette connector
17
Processor socket (populated)
14
ATA controller (primary)
18
Remote Insight Lights-Out
Edition II connector
15
Center wall fan connectors
19
NMI debug button
16
Processor power connector
20
DIMM sockets (1-4)
Installing Additional Memory
Server memory can be expanded by installing Double Data Rate Synchronous
DRAM (DDR SDRAM). The system supports up to four PC2100 ECC registered
DDR SDRAM Dual Inline Memory Modules (DIMMs) installed in four sockets on
the system board. Memory can be added one module at a time.
Refer to Figure 3-4 and to Table 3-1 for DIMM slot location and socket numbers.
This information is also available on the hood label.
The server memory can be expanded to 4 GB. In the maximum memory
configuration, all four DIMM sockets are populated with 1-GB, PC2100 ECC
registered DDR SDRAM DIMMs.
Observe the following guidelines when installing additional memory:
•
•
•
•
•
DIMMs installed in the server must be PC2100 registered DDR SDRAM, 2.5 V,
64 bits wide, and ECC.
All DIMMs installed must be the same speed. Do not install DIMM modules
supporting different speeds, for example, 266 MHz and 200 MHz.
Install the DIMMs in descending sequential order, starting with DIMM socket 4.
Use only HP recommended DIMMs. DIMMs from other sources can adversely
affect data integrity
Use only the 3.05 cm (1.2 inch) DIMMs.
HP ProLiant DL320 Generation 2 Server Setup and Installation Guide
3-7