HP Kayak XA 05xx HP Kayak XA Series 05xx, Upgrade & Configuration Guide - Page 21

Before Installing an, IDE Hard Disk, Before Installing a, SCSI Hard Disk

Get HP Kayak XA 05xx PDF manuals and user guides View all HP Kayak XA 05xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

1 How to Install Accessories In Your Desktop PC Workstation Installing Mass Storage Devices Before Installing an IDE Hard Disk Before Installing a SCSI Hard Disk NOTE Refer to the drive's installation guide to see if you must set jumpers or if there is a special installation procedure to follow. If you are installing an additional SCSI drive, you should assign an unused SCSI ID to this accessory. SCSI IDs range from 0 to 15 for Ultra wide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive and SCSI ID 7 is reserved for the integrated SCSI controller (the default for narrow and wide SCSI devices). You do not need to select a SCSI ID for Plug and Play SCSI hard disks (SCSI hard disks that support the SCAM protocol). You should assign an unused SCSI ID to the second SCSI hard disk drive (for example, SCSI ID 1). The SCSI ID is usually configured with jumpers on the SCSI hard disk drive. Refer to the installation guide supplied with the drive for information on selecting a SCSI ID. Some internal SCSI disk drives may have termination resistors that must be removed or disabled before installation in your computer. Refer to the drive's installation guide for more details and to see if there is a special installation procedure to follow. English 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
English
11
1
How to Install Accessories In Your Desktop PC Workstation
Installing Mass Storage Devices
Before Installing an
IDE Hard Disk
Refer to the drive’s installation guide to see if you must set jumpers or if
there is a special installation procedure to follow.
Before Installing a
SCSI Hard Disk
If you are installing an additional SCSI drive, you should assign an
unused SCSI ID to this accessory. SCSI IDs range from 0 to 15 for Ultra
wide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive and
SCSI ID 7 is reserved for the integrated SCSI controller (the default for
narrow and wide SCSI devices).
NOTE
You do not need to select a SCSI ID for Plug and Play SCSI hard disks
(SCSI hard disks that support the SCAM protocol).
You should assign an unused SCSI ID to the second SCSI hard disk
drive (for example, SCSI ID 1).
The SCSI ID is usually configured with jumpers on the SCSI hard disk
drive. Refer to the installation guide supplied with the drive for
information on selecting a SCSI ID.
Some internal SCSI disk drives may have termination resistors that
must be removed or disabled before installation in your computer.
Refer to the drive’s installation guide for more details and to see if there
is a special installation procedure to follow.