HP Kayak XA 05xx HP Kayak XA Series 05xx, Upgrade & Configuration Guide - Page 52

How to Install Accessories In Your Minitower PC Workstation, Power Cable, Data Cable, Pass the SCSI

Get HP Kayak XA 05xx PDF manuals and user guides View all HP Kayak XA 05xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2 How to Install Accessories In Your Minitower PC Workstation Installing Mass Storage Devices 10 Connect the data and power cables to the rear of the device. (The connectors are shaped to go in one way only.) Data Cable Power Cable 11 If you are installing a SCSI device, pass the SCSI cable through the base of the SCSI holder. You will need to remove then replace the SCSI holder to do this. Pass the SCSI cable through the base of the SCSI holder 12 Slide the power supply back into position, and tighten the four selfretaining screws (see page 32). 13 Replace the HP UltraFlow airflow guide and reconnect the fan to the system board (see the illustration on page 31). 14 Install any other accessories before replacing the cover and completing the installation. 15 Follow the instructions below to complete the installation. 42 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
2
How to Install Accessories In Your Minitower PC Workstation
Installing Mass Storage Devices
42
English
10
Connect the data and power cables to the rear of the device. (
The
connectors are shaped to go in one way only
.)
11
If you are installing a SCSI device, pass the SCSI cable through the
base of the SCSI holder. You will need to remove then replace the
SCSI holder to do this.
12
Slide the power supply back into position, and tighten the four self-
retaining screws (see page 32).
13
Replace the HP UltraFlow airflow guide and reconnect the fan to the
system board (see the illustration on page 31).
14
Install any other accessories before replacing the cover and
completing the installation.
15
Follow the instructions below to complete the installation.
Power Cable
Data Cable
Pass the SCSI cable
through the base of
the SCSI holder