HP Kayak XA 05xx HP Kayak XA Series 05xx, Upgrade & Configuration Guide - Page 70

If you are Unable to Change any Values in, If a POST Error Message is Displayed

Get HP Kayak XA 05xx PDF manuals and user guides View all HP Kayak XA 05xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Rebuild Your PC Workstation's Components 3 Troubleshooting Your HP Kayak PC Workstation If Your PC Workstation Does Not Start Properly 6 Turn on the display and computer. If your PC Workstation still does not start properly, remove all boards and accessories, except the hard disk drive and video board. Start the PC Workstation. If the PC Workstation now works, add the boards and accessories one at a time to determine which one is causing the problem. If you are Unable to Change any Values in Setup Ensure that you are using the correct password. If a POST Error Message is Displayed The Power-On-Self-Test (POST) can detect both an error and a change to the configuration. In either case, an error code and short description is displayed. Depending on the kind of error, you will have one or more of these choices available on screen: • Press F1 to ignore the message and continue. • Press F2 to run Setup and correct a system configuration error. HP recommends that you correct the error before proceeding, even if the PC Workstation appears to start successfully. • Press F4 to accept (validate) the change and update Setup's configuration information. • Press Enter to see more details about the message. After viewing these details, you will be returned to the original POST display screen. If the message is actually a change to the configuration you have made (for example, you have just removed some memory), you can then press F4 to accept the change and update Setup's configuration information. Otherwise, press F1 to ignore the message and continue, or press F2 to run Setup and correct a system configuration error. (The number of choices you will have available are dependent on the kind of error.) 60 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
3
Troubleshooting Your HP Kayak PC Workstation
If Your PC Workstation Does Not Start Properly
60
English
6
Turn on the display and computer.
Rebuild Your PC
Workstation’s
Components
If your PC Workstation still does not start properly, remove all boards
and accessories, except the hard disk drive and video board. Start the
PC Workstation. If the PC Workstation now works, add the boards and
accessories one at a time to determine which one is causing the
problem.
If you are Unable to Change any Values in
Setup
Ensure that you are using the correct password.
If a POST Error Message is Displayed
The Power-On-Self-Test (POST) can detect both an error and a change
to the configuration. In either case, an error code and short description
is displayed. Depending on the kind of error, you will have one or more
of these choices available on screen:
•
Press
F1
to ignore the message and continue.
•
Press
F2
to run
Setup
and correct a system configuration
error
. HP
recommends that you correct the error before proceeding, even if
the PC Workstation appears to start successfully.
•
Press
F4
to accept (validate) the change and update
Setup’s
configuration information.
•
Press
Enter
to see more details about the message. After viewing
these details, you will be returned to the original POST display
screen. If the message is actually a change to the configuration you
have made (for example, you have just removed some memory), you
can then press
F4
to accept the change and update
Setup’s
configuration information. Otherwise, press
F1
to ignore the
message and continue, or press
F2
to run
Setup
and correct a system
configuration error. (The number of choices you will have available
are dependent on the kind of error.)