HP LaserJet MFP M232-M237 User Guide - Page 94

Table 8-17, Description, Sample, Possible solutions, Output curl, Positive curl, Negative curl

Get HP LaserJet MFP M232-M237 PDF manuals and user guides View all HP LaserJet MFP M232-M237 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Table 8-17 Output defects Description Sample Output curl: Printed paper has curled edges. The curled edge can be along the short or long side of the paper. Two types of curl are possible: ● Positive curl: The paper curls toward the printed side. The defect occurs in dry environments or when printing high coverage pages. ● Negative curl: The paper curls away from the printed side. The defect occurs in high-humidity environments or when printing low coverage pages. Output stacking: The paper does not stack well in the output tray. The stack might be uneven, skewed, or the pages might be pushed out of the tray and onto the floor. Any of the following conditions can cause this defect: ● Extreme paper curl ● The paper in the tray is wrinkled or deformed ● The paper is a non-standard paper type, such as envelopes ● The output tray is too full Possible solutions 1. Reprint the document. 2. Positive curl: From the printer EWS, select a heavier paper type. The heavier paper type creates a higher temperature for printing. Negative curl: From the printer EWS, select a lighter paper type. The lighter paper type creates a lower temperature for printing. Try storing the paper in a dry environment prior or use freshly opened paper. 3. Print in duplex mode. 4. If the problem persists, go to www.hp.com/support/ljM232MFP 1. Reprint the document. 2. Extend the output bin extension. 3. If the defect is caused by extreme paper curl, complete the troubleshooting steps for Output curl. 4. Use a different paper type. 5. Use freshly opened paper. 6. Remove the paper from the output tray before the tray gets too full. 7. If the problem persists, go to www.hp.com/support/ljM232MFP 88 Chapter 8 Solve problems ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Table 8-17
Output defects
Description
Sample
Possible solutions
Output curl:
Printed paper has curled edges. The curled
edge can be along the short or long side of
the paper. Two types of curl are possible:
●
Positive curl:
The paper curls toward
the printed side. The defect occurs in
dry environments or when printing
high coverage pages.
●
Negative curl:
The paper curls away
from the printed side. The defect
occurs in high-humidity
environments or when printing low
coverage pages.
1.
Reprint the document.
2.
Positive curl:
From the printer EWS,
select a heavier paper type. The
heavier paper type creates a higher
temperature for printing.
Negative curl:
From the printer EWS,
select a lighter paper type. The
lighter paper type creates a lower
temperature for printing. Try storing
the paper in a dry environment prior
or use freshly opened paper.
3.
Print in duplex mode.
4.
If the problem persists, go to
www.hp.com/
support/ljM232MFP
Output stacking:
The paper does not stack well in the output
tray. The stack might be uneven, skewed,
or the pages might be pushed out of the
tray and onto the floor. Any of the
following conditions can cause this defect:
●
Extreme paper curl
●
The paper in the tray is wrinkled or
deformed
●
The paper is a non-standard paper
type, such as envelopes
●
The output tray is too full
1.
Reprint the document.
2.
Extend the output bin extension.
3.
If the defect is caused by extreme
paper curl, complete the
troubleshooting steps for Output
curl.
4.
Use a different paper type.
5.
Use freshly opened paper.
6.
Remove the paper from the output
tray before the tray gets too full.
7.
If the problem persists, go to
www.hp.com/
support/ljM232MFP
88
Chapter 8
Solve problems
ENWW