HP Photosmart C6300 Basic Guide - Page 9

Set up the HP All-in-One using an ad hoc wireless connection, Infrastructure, WEP encryption - all in one series

Get HP Photosmart C6300 - All-in-One Printer PDF manuals and user guides View all HP Photosmart C6300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

c. When you are finished entering the new SSID, use the arrow buttons to highlight Done on the visual keyboard, and then press OK. d. Press the down arrow button until Infrastructure is highlighted, and then press OK. e. Press the down arrow button until WEP encryption or WPA encryption is highlighted, and then press OK. If you do not want to use WEP encryption, press the down arrow button until No, my network does not use encryption is highlighted, and then press OK. Go to step 7. 6. If prompted, enter your WPA or WEP key as follows: a. Use the arrow buttons to highlight a letter or number on the visual keyboard, and then press OK to select it. NOTE: You must enter the exact uppercase (capital) and lowercase (small) letters. Otherwise, the wireless connection will fail. b. When you are finished entering the WPA or WEP key, use the arrow buttons to highlight Done on the visual keyboard. c. Press OK to confirm. The product will attempt to connect to the network. If a message says you entered an invalid WPA or WEP key, check the key you wrote down for your new network, follow the prompts to correct the key, and then try again. The wireless network test runs, performing a series of diagnostic tests to determine whether network setup is successful. The wireless network test prints upon completion of the test. 7. When the product connects successfully to the network, go to your computer to install the software on each computer that will use the network. Set up the HP All-in-One using an ad hoc wireless connection Use this section if you want to connect the HP All-in-One to a wireless-capable computer without using a wireless router or access point. Network setup Set up the HP All-in-One using an ad hoc wireless connection 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
c
.
When you are finished entering the new SSID, use the arrow buttons to highlight
Done
on the visual keyboard, and then press
OK
.
d
.
Press the down arrow button until
Infrastructure
is highlighted, and then press
OK
.
e
.
Press the down arrow button until
WEP encryption
or
WPA encryption
is
highlighted, and then press
OK
.
If you do
not
want to use WEP encryption, press the down arrow button until
No,
my network does not use encryption
is highlighted, and then press
OK
. Go to
step 7.
6.
If prompted, enter your WPA or WEP key as follows:
a
.
Use the arrow buttons to highlight a letter or number on the visual keyboard, and
then press
OK
to select it.
NOTE:
You must enter the
exact
uppercase (capital) and lowercase (small)
letters. Otherwise, the wireless connection will fail.
b
.
When you are finished entering the WPA or WEP key, use the arrow buttons to
highlight
Done
on the visual keyboard.
c
.
Press
OK
to confirm.
The product will attempt to connect to the network. If a message says you entered
an invalid WPA or WEP key, check the key you wrote down for your new network,
follow the prompts to correct the key, and then try again.
The wireless network test runs, performing a series of diagnostic tests to determine
whether network setup is successful. The wireless network test prints upon
completion of the test.
7.
When the product connects successfully to the network, go to your computer to install
the software on each computer that will use the network.
Set up the HP All-in-One using an ad hoc wireless
connection
Use this section if you want to connect the HP All-in-One to a wireless-capable computer
without using a wireless router or access point.
Set up the HP All-in-One using an ad hoc wireless connection
7
Network setup