HP ProLiant DL980 HP ProLiant Servers Troubleshooting Guide - Page 101

Loose Cable Detected - Logical Drives May Be Marked FAILED Until Corrected

Get HP ProLiant DL980 - G7 Server PDF manuals and user guides View all HP ProLiant DL980 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Logical Drive X Status = Recovering (rebuilding data on a replaced drive) Description: A physical drive in this logical drive has failed and has now been replaced. The replaced drive is rebuilding from the mirror drive or the parity data. Action: No action is required. Normal operations can occur; however, performance will be less than optimal until after the rebuild process completes. Logical Drive X Status = Wrong Drive Replaced Description: A physical drive in this logical drive has failed. The incorrect drive was replaced. Action: 1. Power down the server. 2. Replace the drive that was incorrectly replaced. 3. Replace the original drive that failed with a new drive. CAUTION: Do not run the server setup utility and try to reconfigure, or data will be lost. Loose Cable Detected - Logical Drives May Be Marked FAILED Until Corrected Description: At power up, the system does not detect a configured physical drive or an external storage unit that was previously detected before the last system shutdown. This event can occur if the user removes one or more drives after the system is powered down or if a loose cable or malfunction prevents the drives from spinning up. Action: If a drive or enclosure has been removed or disconnected, do the following: 1. Power down the server. 2. Check cabling. 3. Power up the server and storage enclosure at the same time. If drives are failed or purposely removed while the system is off: 1. Reboot the server. 2. When prompted during POST, press F2 to fail the missing drives. Mirror Data Miscompare Description: Data was found at reset initialization in the posted-write memory; however, the mirror data compare test failed resulting in that data being marked as invalid. Data loss is possible. Action: Replace the array accelerator board. No Configuration for Array Accelerator Board Description: The array accelerator board has not been configured. Action: If the array accelerator board is present, run ACU ("Array Configuration Utility" on page 70) to configure the board. Error messages 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Error messages 101
Logical Drive X Status = Recovering (rebuilding data on a replaced drive)
Description
: A physical drive in this logical drive has failed and has now been replaced. The replaced
drive is rebuilding from the mirror drive or the parity data.
Action
: No action is required. Normal operations can occur; however, performance will be less than
optimal until after the rebuild process completes.
Logical Drive X Status = Wrong Drive Replaced
Description
: A physical drive in this logical drive has failed. The incorrect drive was replaced.
Action
:
1.
Power down the server.
2.
Replace the drive that was incorrectly replaced.
3.
Replace the original drive that failed with a new drive.
CAUTION:
Do not run the server setup utility and try to reconfigure, or data will be lost.
Loose Cable Detected - Logical Drives May Be Marked FAILED Until Corrected
Description
: At power up, the system does not detect a configured physical drive or an external storage
unit that was previously detected before the last system shutdown. This event can occur if the user removes
one or more drives after the system is powered down or if a loose cable or malfunction prevents the
drives from spinning up.
Action
: If a drive or enclosure has been removed or disconnected, do the following:
1.
Power down the server.
2.
Check cabling.
3.
Power up the server and storage enclosure at the same time.
If drives are failed or purposely removed while the system is off:
1.
Reboot the server.
2.
When prompted during POST, press F2 to fail the missing drives.
Mirror Data Miscompare
Description
: Data was found at reset initialization in the posted-write memory; however, the mirror data
compare test failed resulting in that data being marked as invalid. Data loss is possible.
Action
: Replace the array accelerator board.
No Configuration for Array Accelerator Board
Description
: The array accelerator board has not been configured.
Action
: If the array accelerator board is present, run ACU ("
Array Configuration Utility
" on page
70
) to
configure the board.