Home » HP Manuals » Servers » HP ProLiant DL980 » Manual Viewer

HP ProLiant DL980 HP ProLiant Servers Troubleshooting Guide - Page 77

Remote support and analysis tools, Keeping the system current

Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Remote support and analysis tools HP Insight Remote Support software HP Insight Remote Support software delivers secure remote support for your HP Servers and Storage, 24 X 7, so you can spend less time solving problems and more time focused on your business. You can have your systems remotely monitored for hardware failure using secure technology that has been proven at thousands of companies around the world. In many cases, you can avoid problems before they occur. There are two HP Insight Remote Support solutions: • For small and midsize environments: HP Insight Remote Support Standard provides basic remote monitoring, notification/advisories and service dispatch. It is optimized for environments with 1 to 50 servers and can be installed on a shared HP ProLiant Windows application server. The software supports HP EVA storage devices, HP ProLiant, BladeSystems, HP Integrity and HP 9000 servers running Microsoft Windows, Red Hat Enterprise Linux, Novell SUSE and Novell Netware. Download from the HP website (http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=RSSWMBA SE). • For midsize and large environments: HP Insight Remote Support Pack (formerly Service Essentials Remote Support Pack) is targeted for larger environments and is integrated with HP Systems Insight Manager (SIM). It provides comprehensive remote monitoring, notification/advisories, dispatch and proactive service support for nearly all HP servers, storage, network and SAN environments, plus selected Dell and IBM Windows servers that have a support obligation with HP. It also enables HP to deliver higher levels of proactive support in line with HP Mission Critical Services support agreements. Download from the HP website (http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=ISDVD). Both HP Insight Remote Support solutions are available at no additional cost to customers with a valid warranty on HP technology, an HP Care Pack Service or HP contractual support agreement. For more information, see the HP website (http://www.hp.com/go/insightremotesupport). Keeping the system current Drivers IMPORTANT: Always perform a backup before installing or updating device drivers. The server includes new hardware that may not have driver support on all OS installation media. If you are installing a SmartStart-supported OS, use the SmartStart software (on page 67) and its Assisted Path feature to install the OS and latest driver support. If you are installing drivers from the SmartStart CD, be sure that you are using the latest SmartStart version that your server supports. To verify that your server is using the latest supported version, see the HP website (http://www.hp.com/support). For more information, see the documentation provided with the SmartStart CD. Software tools and solutions 77

Section	Page
HP ProLiant ServersTroubleshooting Guide	1
Notice	2
Contents	3
Introduction	8
What's new	8
Revision history	8
375445-xx8 (July 2009)	8
375445-xx7 (November 2008)	9
375445-xx6 (September 2007)	10
375445-xx5 (June 2006)	10
375445-xx4 (May 2006)	10
375445-xx3 (September 2005)	11
Getting started	12
HP ProLiant 100 Series Server troubleshooting information	12
How to use this guide	12
Pre-diagnostic steps	13
Important safety information	13
Symbols on equipment	13
Warnings and cautions	14
Electrostatic discharge	15
Preventing electrostatic discharge	15
Grounding methods to prevent electrostatic discharge	15
Symptom information	16
Prepare the server for diagnosis	16
Breaking the server down to the minimum hardware configuration	17
Common problem resolution	18
Loose connections	18
Service notifications	18
Firmware updates	18
DIMM handling guidelines	19
Hard drive guidelines	19
SAS and SATA hard drive guidelines	19
SCSI hard drive guidelines	19
Hard drive LED combinations	20
Hot-plug SCSI hard drive LED combinations	20
SAS and SATA hard drive LED combinations	20
Server updates with an HP Trusted Platform Module and BitLocker™ enabled	21
Diagnostic flowcharts	23
Troubleshooting flowcharts	23
Troubleshooting flowchart reference websites	23
Start diagnosis flowchart	25
General diagnosis flowchart	25
Power-on problems flowchart	27
Server power-on problems flowchart	27
p-Class server blade power-on problems flowchart	29
c-Class server blade power-on problems flowchart	29
POST problems flowchart	30
Server and p-Class server blade POST problems flowchart	31
c-Class server blade POST problems flowchart	32
Operating system boot problems flowchart	32
Server fault indications flowchart	33
Server and p-Class server blade fault indications flowchart	34
c-Class server blade fault indications flowchart	36
Hardware problems	37
Procedures for all ProLiant servers	37
Power problems	37
Power source problems	37
Power supply problems	37
UPS problems	38
UPS is not working properly	38
Low battery warning is displayed	38
One or more LEDs on the UPS is red	38
General hardware problems	39
Problems with new hardware	39
Unknown problem	40
Third-party device problems	40
Testing the device	40
Internal system problems	41
Battery pack problems	41
The battery stops charging or begins to swell	41
CD-ROM and DVD drive problems	41
System does not boot from the drive	41
Data read from the drive is inconsistent, or drive cannot read data	42
Drive is not detected	42
Diskette drive problems	42
Diskette drive light stays on	42
A problem has occurred with a diskette transaction	42
Diskette drive cannot read a diskette	42
Drive is not found	43
Non-system disk message is displayed	43
Diskette drive cannot write to a diskette	43
Drive problems (hard drives and solid state drives)	43
HP SIM reports a drive fault on a parallel SCSI hard drive managed by an HP Smart Array controller	43
The fault LED is illuminated on a parallel SCSI hard drive managed by an HP Smart Array controller	43
System completes POST but drive fails	44
No hard drives are recognized	44
Hard drive is not recognized by the server	44
A new hard drive is not recognized	45
Data is inaccessible	45
Server response time is slower than usual	45
SD card problems	46
System does not boot from the drive	46
USB drive key problems	46
System does not boot from the drive	46
Fan problems	46
General fan problems are occurring	46
Hot-plug fan problems are occurring	46
All fans in an HP BladeSystem c-Class enclosure are operating at a high speed	47
All fans in an HP ProLiant G6 server are not spinning or are not spinning at the same speed	47
HP Trusted Platform Module problems	47
Memory problems	48
General memory problems are occurring	48
Server is out of memory	48
Memory count error exists	48
Server fails to recognize existing memory	49
Server fails to recognize new memory	49
Server fails to boot, all DIMM LEDs illuminate amber, ....	49
PPM problems	50
Processor problems	50
Tape drive problems	51
Stuck tape issue	51
Read/write issue	51
Backup issue	51
Media issue	52
Graphics and video adapter problems	52
General graphics and video adapter problems are occurring	52
System open circuits and short circuits	53
External device problems	53
Video problems	53
Screen is blank for more than 60 seconds after you power up the server	53
Monitor does not function properly with energy saver features	54
Video colors are wrong	54
Slow-moving horizontal lines are displayed	54
Mouse and keyboard problems	54
Audio problems	55
Printer problems	55
Printer does not print	55
Printer output is garbled	55
Cable problems	55
Drive errors, retries, timeouts, and unwarranted drive failures when using an older Mini SAS cable	55
Local I/O cable problems	55
Modem problems	56
No dial tone exists	56
No response occurs when you type AT commands	56
AT commands are not visible	56
Data is displayed as garbled characters after the connection is established	56
Modem does not answer an incoming call	56
Modem does not connect to another modem	57
Modem disconnects while online	57
AT command initialization string is not working	57
Connection errors are occurring	57
You are unable to connect to an online subscription service	57
You are unable to connect at 56 Kbps	58
Network controller problems	58
Network controller is installed but not working	58
Network controller has stopped working	58
Network controller stopped working when an expansion board was added	59
Problems are occurring with the network interconnect blades	59
Expansion board problems	59
System requests recovery method during expansion board replacement	59
Software problems	60
Operating system problems and resolutions	60
Operating system problems	60
Operating system locks up	60
General protection fault occurs	60
Errors are displayed in the error log	61
Problems occur after the installation of a service pack	61
NetWare attempts to load MEGA4 XX.HAM or 120PCI.HAM during installation, and a RILOE II board is installed	61
During installation of Sun Solaris, the system locks up or a panic error occurs	61
Operating system issues with Intel® dual-core processors (Hyper-Threading enabled)	61
Operating system updates	61
Restoring to a backed-up version	62
When to Reconfigure or Reload Software	62
Linux operating systems	63
Application software problems	63
Software locks up	63
Errors occur after a software setting is changed	63
Errors occur after the system software is changed	63
Errors occur after an application is installed	63
ROM problems	64
Remote ROM flash problems	64
General remote ROM flash problems are occurring	64
Command-line syntax error	64
Access denied on target computer	64
Invalid or incorrect command-line parameters	64
Network connection fails on remote communication	65
Failure occurs during ROM flash	65
Target system is not supported	65
System requests recovery method during a firmware update	65
Boot problems	65
Server does not boot	65
Software tools and solutions	67
Configuration tools	67
SmartStart software	67
SmartStart Scripting Toolkit	67
HP ROM-Based Setup Utility	67
Using RBSU	68
Auto-configuration process	68
Boot options	69
BIOS Serial Console	69
Configuring AMP modes	69
Array Configuration Utility	70
Diagnostics tasks	70
Option ROM Configuration for Arrays	71
Re-entering the serial number and product ID	71
Management tools	72
Automatic Server Recovery	72
ROMPaq utility	72
Remote Insight Lights-Out Edition II	73
iLO and iLO 2 technology	73
Integrated Lights-Out 3 technology	73
Erase Utility	74
Redundant ROM support	74
Safety and security benefits	74
USB support	74
Diagnostic tools	75
HP Insight Diagnostics	75
Smart Array SCSI Diagnosis feature	75
HP Insight Diagnostics survey functionality	75
Integrated Management Log	76
Array diagnostic software	76
Remote support and analysis tools	77
HP Insight Remote Support software	77
Keeping the system current	77
Drivers	77
Version control	78
ProLiant Support Packs	78
Operating system version support	78
Firmware	78
HP Smart Update Manager	79
System Online ROM flash component utility	79
Subscriber's choice	80
Change control and proactive notification	80
Care Pack	80
Firmware maintenance	80
Types of ROM	80
System ROM	80
Redundant ROM support	81
Disaster recovery support	81
Automatic backup	81
Option ROMs	81
Verifying firmware versions	82
Updating firmware	82
ROMPaq utility diskette or USB drive key	82
System ROMPaq Firmware Upgrade Utility	83
HP Smart Update Manager deployment	83
Offline deployment	84
Online deployment	84
ROM Update Utility	84
Unsupported processor stepping with Intel® processors	85
Updating system ROM without removing the processor	85
Updating system ROM after removing the processor	85
Unsupported processor stepping with AMD processors	85
HP resources for troubleshooting	86
Online resources	86
HP Technical Support website	86
HP Guided Troubleshooting website	86
Server documentation	86
White papers	86
Service notifications, advisories, and notices	86
Subscription services	86
HP Care Pack Services	87
Product information resources	87
Additional product information	87
Registering the server	87
Overview of server features and installation instructions	87
Key features, option part numbers	87
Server and option specifications, symbols, installation warnings, and notices	87
Teardown procedures, part numbers, specifications	88
Technical topics	88
Product installation resources	88
Switch settings, LED functions, drive, memory, expansion board and processor installation instructions, and board layouts	88
External cabling information	88
Power capacity	88
Product configuration resources	88
Device driver information	88
DDR3 memory configuration	89
Operating System Version Support	89
Operating system installation and configuration information (for factory-installed operating systems)	89
Server configuration information	89
Installation and configuration information for the server setup software	89
Software installation and configuration of the server	89
iLO information	89
Management of the server	89
Installation and configuration information for the server management system	90
Fault tolerance, security, care and maintenance, configuration and setup	90
Error messages	91
ADU error messages	91
Introduction to ADU error messages	91
Accelerator Board not Detected	91
Accelerator Error Log	91
Accelerator Parity Read Errors: X	91
Accelerator Parity Write Errors: X	91
Accelerator Status: Cache was Automatically Configured During Last Controller Reset	92
Accelerator Status: Data in the Cache was Lost...	92
Accelerator Status: Dirty Data Detected has Reached Limit...	92
Accelerator Status: Dirty Data Detected...	92
Accelerator Status: Excessive ECC Errors Detected in at Least One Cache Line...	92
Accelerator Status: Excessive ECC Errors Detected in Multiple Cache Lines...	92
Accelerator Status: Obsolete Data Detected	93
Accelerator Status: Obsolete Data was Discarded	93
Accelerator Status: Obsolete Data was Flushed (Written) to Drives	93
Accelerator Status: Permanently Disabled	93
Accelerator Status: Possible Data Loss in Cache	93
Accelerator Status: Temporarily Disabled	93
Accelerator Status: Unrecognized Status	93
Accelerator Status: Valid Data Found at Reset	93
Accelerator Status: Warranty Alert	94
Adapter/NVRAM ID Mismatch	94
Array Accelerator Battery Pack X not Fully Charged	94
Array Accelerator Battery Pack X Below Reference Voltage (Recharging)	94
Board in Use by Expand Operation	94
Board not Attached	94
Cache Has Been Disabled Because ADG Enabler Dongle is Broken or Missing	94
Cache Has Been Disabled; Likely Caused By a Loose Pin on One of the RAM Chips	94
Configuration Signature is Zero	95
Configuration Signature Mismatch	95
Controller Communication Failure Occurred	95
Controller Detected. NVRAM Configuration not Present	95
Controller Firmware Needs Upgrading	95
Controller is Located in Special \	95
Controller Is Not Configured	95
Controller Reported POST Error. Error Code: X	96
Controller Restarted with a Signature of Zero	96
Disable Command Issued	96
Drive (Bay) X Firmware Needs Upgrading	96
Drive (Bay) X has Insufficient Capacity for its Configuration	96
Drive (Bay) X has Invalid M&P Stamp	96
Drive (Bay) X Has Loose Cable	96
Drive (Bay) X is a Replacement Drive	97
Drive (Bay) X is a Replacement Drive Marked OK	97
Drive (Bay) X is Failed	97
Drive (Bay) X is Undergoing Drive Recovery	97
Drive (Bay) X Upload Code Not Readable	97
Drive (Bay) X Was Inadvertently Replaced	97
Drive Monitoring Features Are Unobtainable	98
Drive Monitoring is NOT Enabled for SCSI Port X Drive ID Y	98
Drive Time-Out Occurred on Physical Drive Bay X	98
Drive X Indicates Position Y	98
Duplicate Write Memory Error	98
Error Occurred Reading RIS Copy from SCSI Port X Drive ID	98
FYI: Drive (Bay) X is Third-Party Supplied	98
Identify Logical Drive Data did not Match with NVRAM	99
Insufficient adapter resources	99
Inter-Controller Link Connection Could Not Be Established	99
Less Than 75% Batteries at Sufficient Voltage	99
Less Than 75% of Batteries at Sufficient Voltage Battery Pack X Below Reference Voltage	99
Logical Drive X Failed Due to Cache Error	99
Logical Drive X Status = Failed	99
Logical Drive X Status = Interim Recovery (Volume Functional, but not Fault Tolerant)	100
Logical Drive X Status = Loose Cable Detected...	100
Logical Drive X Status = Overheated	100
Logical Drive X Status = Overheating	100
Logical Drive X Status = Recovering (rebuilding data on a replaced drive)	101
Logical Drive X Status = Wrong Drive Replaced	101
Loose Cable Detected - Logical Drives May Be Marked FAILED Until Corrected	101
Mirror Data Miscompare	101
No Configuration for Array Accelerator Board	101
One or More Drives is Unable to Support Redundant Controller Operation	102
Other Controller Indicates Different Hardware Model	102
Other Controller Indicates Different Firmware Version	102
Other Controller Indicates Different Cache Size	102
Processor Reduced Power Mode Enabled in RBSU	102
Processor Not Started (Processor Stalled)	102
Processor Not Started (Stepping Does Not Match)	102
Processor Not Started (Unsupported Processor Stepping)	102
Processor Not Supported (Unsupported Core Speed)	102
RIS Copies Between Drives Do Not Match	103
SCSI Port X Drive ID Y Failed - REPLACE (failure message)	103
SCSI Port X, Drive ID Y Firmware Needs Upgrading	103
SCSI Port X, Drive ID Y Has Exceeded the Following Threshold(s)	103
SCSI Port X, Drive ID Y is not Stamped for Monitoring	103
SCSI Port X, Drive ID Y May Have a Loose Connection...	103
SCSI Port X, Drive ID Y RIS Copies Within This Drive Do Not Match	104
SCSI Port X, Drive ID Y...S.M.A.R.T. Predictive Failure Errors Have Been Detected in the Factory Monitor and Performance Data...	104
SCSI Port X, Drive ID Y...S.M.A.R.T. Predictive Failure Errors Have Been Detected in the Power Monitor and Performance Data...	104
SCSI Port X, Drive ID Y Was Replaced On a Good Volume: (failure message)	104
Set Configuration Command Issued	104
Soft firmware upgrade required	105
Storage Enclosure on SCSI Bus X has a Cabling Error (Bus Disabled)...	105
Storage Enclosure on SCSI Bus X Indicated a Door Alert...	105
Storage Enclosure on SCSI Bus X Indicated a Power Supply Failure...	105
Storage Enclosure on SCSI Bus X Indicated an Overheated Condition...	105
Storage enclosure on SCSI Bus X is unsupported with its current firmware version...	105
Storage Enclosure on SCSI Bus X Indicated that the Fan Failed...	105
Storage Enclosure on SCSI Bus X Indicated that the Fan is Degraded...	106
Storage Enclosure on SCSI Bus X Indicated that the Fan Module is Unplugged...	106
Storage Enclosure on SCSI Bus X - Wide SCSI Transfer Failed...	106
Swapped cables or configuration error detected. A configured array of drives...	106
Swapped Cables or Configuration Error Detected. A Drive Rearrangement...	106
Swapped Cables or Configuration Error Detected. An Unsupported Drive Arrangement Was Attempted...	107
Swapped cables or configuration error detected. The cables appear to be interchanged...	107
Swapped cables or configuration error detected. The configuration information on the attached drives...	107
Swapped Cables or Configuration Error Detected. The Maximum Logical Volume Count X...	107
System Board is Unable to Identify which Slots the Controllers are in	108
The Redundant Controllers Installed are not the Same Model...	108
This Controller Can See the Drives but the Other Controller Can't	108
This Controller Can't See the Drives but the Other Controller Can	108
Unable to Communicate with Drive on SCSI Port X, Drive ID Y	109
Unable to Retrieve Identify Controller Data. Controller May be Disabled or Failed	109
Unknown Disable Code	109
Unrecoverable Read Error	109
Unsupported Processor Configuration (Processor Required in Slot #1)	109
Warning Bit Detected	109
WARNING - Drive Write Cache is Enabled on X	110
WARNING - Mixed Feature Processors Were Detected	110
WARNING - Resetting Corrupted CMOS	110
WARNING - Resetting Corrupted NVRAM	110
WARNING - Resetting Corrupted System Environment	110
WARNING - Restoring Default Configurations as Requested	110
WARNING: Storage Enclosure on SCSI Bus X Indicated it is Operating in Single Ended Mode...	110
Write Memory Error	111
Wrong Accelerator	111
ADU version 8.0 through 8.28 error messages	111
Array Accelerator: The batteries were hot-removed.	111
Array Accelerator: The cache is disabled because the batteries are low on the redundant controller.	111
Array Accelerator: The cache for this controller is temporarily disabled since a snapshot is in progress....	111
Array Accelerator: The cache is disabled because the batteries are low.	111
Array Accelerator: This controller has been set up to be a part of a redundant pair of controllers...	112
Array status: The array has failed.	112
Controller State: A logical drive is configured with a newer version of the Array Configuration tools than is currently running.	112
Controller State: The HBA does not have an access ID...	112
Drive Offline due to Erase Operation: The logical drive is offline from having an erase in progress.	112
Drive Offline due to Erase Operation: The physical drive is currently queued for erase.	112
Drive Offline due to Erase Operation: The physical drive is offline and currently being erased.	112
Drive Offline due to Erase Operation: The physical drive is offline and the erase process has been failed...	112
Drive Offline due to Erase Operation: The physical drive is offline and the erase process has completed...	113
Drive Offline due to Erase Operation: The physical drive is offline from having an erase in progress.	113
Logical drive state: A logical drive is configured with a newer version of Storage/Config Mod than is currently running.	113
Logical drive state: Background parity initialization is currently queued...	113
Logical drive state: The current array controller is performing capacity expansion,...	113
Logical drive state: The logical drive is disabled from a SCSI ID conflict.	113
Logical drive state: The logical drive is not configured.	113
Logical drive state: The logical drive is not yet available.	113
Logical drive state: The logical drive is offline from being ejected.	113
Logical drive state: The logical drive is queued for erase.	114
Logical drive state: The logical drive is queued for expansion.	114
Logical drive state: The logical drive is queued for rebuilding.	114
Logical drive state: This logical drive has a high physical drive count...	114
NVRAM Error: Board ID could not be read...	114
NVRAM Error: Bootstrap NVRAM image failed checksum test,...	114
NVRAM Error: Bootstrap NVRAM image failed checksum test...	114
Physical Drive State: The data on the physical drive is being rebuilt.	114
Physical Drive State: This drive is not supported for configuration...	114
Redundancy State: This controller has been setup to be part of a redundant pair of controllers....	114
Redundancy State: This controller has been setup to be part of a redundant pair of controllers....	115
Redundant Path Failure: Multi-domain path failure	115
Redundant Path Failure: The logical drive is degraded due to the loss of a redundant path.	115
Redundant Path Failure: The physical drive is degraded due to the loss of a redundant path.	115
Redundant Path Failure: Warning: Redundant I/0 modules of this storage box...	115
POST error messages and beep codes	115
Introduction to POST error messages	115
Non-numeric messages or beeps only	116
Advanced Memory Protection mode: Advanced ECC	116
Advanced Memory Protection mode: Advanced ECC with hot-add support	116
Advanced Memory Protection mode: Online spare with Advanced ECC	116
Advanced Memory Protection mode: Multi-board mirrored memory with Advanced ECC	116
Advanced Memory Protection mode: RAID memory with Advanced ECC	116
An Unexpected Shutdown occurred prior to this power-up	116
Critical Error Occurred Prior to this Power-Up	117
Fan Solution Not Fully Redundant	117
Fan Solution Not Sufficient	117
Fatal DMA Error	117
Fatal Express Port Error	117
Fatal Front Side Bus Error	117
Fatal Global Protocol Error	118
Fatal Hub Link Error	118
FATAL ROM ERROR: The System ROM is not Properly Programmed.	118
Fibre Channel Mezzanine/Balcony Not Supported.	118
High Temperature Condition detected by Processor X	118
Illegal Opcode - System Halted	118
iLO Generated NMI	119
Internal CPU Check - Processor	119
Invalid memory types were found on the same node. Please check DIMM compatibility. - Some DIMMs may not be used	119
Invalid Password - System Halted!	119
Invalid Password - System Restricted!	119
Memory found on unpopulated Node. — Processor is required to be installed for memory to be used.	119
Mismatched power supplies not supported	120
Mixed processor speeds detected. Please make sure that all processors are the same speed. — System Halted!	120
Network Server Mode Active and No Keyboard Attached	120
NMI - Button Pressed!	120
NMI - Undetermined Source	120
Node Interleaving disabled - Invalid memory configuration	120
No Floppy Drive Present	121
No Keyboard Present	121
Parity Check 2 - System DIMM Memory	121
PCI Bus Parity Error, PCI Slot X	121
Power Fault Detected in Hot-Plug PCI Slot X	121
Power Supply Solution Not Fully Redundant	122
Processor X Unsupported Wattage.	122
Redundant ROM Detected - This system contains a valid backup system ROM.	122
REDUNDANT ROM ERROR: Backup ROM Invalid. - ...	122
REDUNDANT ROM ERROR: Bootblock Invalid. - ...	122
REDUNDANT ROM ERROR: Primary ROM invalid. Booting Backup ROM. -...	122
Temperature violation detected - system Shutting Down in X seconds	123
There must be a first DIMM in pair if second DIMM in pair is populated. Second DIMM in pair ignored.	123
This DIMM does not support thermal monitoring...	123
This system only supports 667 MHz Front Side Bus Speed Processors. One or more 800 MHz Front Side Bus Speed Processors have been initialized at 667 MHz. System Halted!	123
Unsupported DIMM(s) found in system. - DIMM(s) may not be used	123
Unsupported PCI Card Detected Remove PCI Card from Slot	123
Unsupported power supply detected in bay X	124
Unsupported Processor Detected System will ONLY boot ROMPAQ Utility. System Halted.	124
USB Tape-based One button Disaster Recovery (OBDR) drive detected.	124
WARNING: A Type 2 Header PCI Device Has Been Detected...	124
WARNING - iLO 2 not responding. System health monitoring has been disabled.	125
WARNING - Mixed Stepping Processors were detected. System cannot proceed.	125
WARNING: ProLiant Demand Based Power Management cannot be supported with the following processor configuration. The system will run in Full Performance mode.	125
100 Series	125
101-I/O ROM Error	125
101-ROM Error	126

Match case Limit results 1 per page

Software tools and solutions

Remote support and analysis tools

HP Insight Remote Support software

HP Insight Remote Support software delivers secure remote support for your HP Servers and Storage, 24 X

7, so you can spend less time solving problems and more time focused on your business. You can have

your systems remotely monitored for hardware failure using secure technology that has been proven at

thousands of companies around the world. In many cases, you can avoid problems before they occur.

There are two HP Insight Remote Support solutions:

•

For small and midsize environments: HP Insight Remote Support Standard provides basic remote

monitoring, notification/advisories and service dispatch. It is optimized for environments with 1 to

50 servers and can be installed on a shared HP ProLiant Windows application server. The software

supports HP EVA storage devices, HP ProLiant, BladeSystems, HP Integrity and HP 9000 servers

running Microsoft Windows, Red Hat Enterprise Linux, Novell SUSE and Novell Netware. Download

from the HP website

(

http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=RSSWMBA

•

For midsize and large environments: HP Insight Remote Support Pack (formerly Service Essentials

Remote Support Pack) is targeted for larger environments and is integrated with HP Systems Insight

Manager (SIM). It provides comprehensive remote monitoring, notification/advisories, dispatch and

proactive service support for nearly all HP servers, storage, network and SAN environments, plus

selected Dell and IBM Windows servers that have a support obligation with HP. It also enables HP to

deliver higher levels of proactive support in line with HP Mission Critical Services support

agreements. Download from the HP website

(

http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=ISDVD

Both HP Insight Remote Support solutions are available at no additional cost to customers with a valid

warranty on HP technology, an HP Care Pack Service or HP contractual support agreement.

For more information, see the HP website (

http://www.hp.com/go/insightremotesupport

Keeping the system current

Drivers

IMPORTANT:

Always perform a backup before installing or updating device drivers.

The server includes new hardware that may not have driver support on all OS installation media.

If you are installing a SmartStart-supported OS, use the SmartStart software (on page

) and its Assisted

Path feature to install the OS and latest driver support.

If you are installing drivers from the SmartStart CD, be sure that you are using the latest SmartStart version

that your server supports. To verify that your server is using the latest supported version, see the HP

website (

http://www.hp.com/support

). For more information, see the documentation provided with the

SmartStart CD.