HP Server rp7420 HP 9000 rp7420 Server - User Service Guide, Fifth Edition - Page 58

Configuring LAN Information For the MP, The MP Main Menu is displayed

Get HP Server rp7420 PDF manuals and user guides View all HP Server rp7420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

• When power is first applied. The BPS LEDs flash amber. • After 30 seconds has elapsed. The flashing amber BPS LED for each BPS becomes a flashing green LED. To interpret LED indicators, see the power cord policies. 3. Log in to the MP: a. Enter Admin at the login prompt. The login is case sensitive. It takes a few moments for the MP prompt to display. If it does not display, verify the laptop serial device settings are correct: 8 bits, no parity, 9600 baud, and na for both Receive and Transmit. Then, try again. b. Enter Admin at the password prompt. The password is case sensitive. The MP Main Menu is displayed: Figure 4-7 MP Main Menu Configuring LAN Information For the MP To set the MP LAN IP address, follow these steps: 1. At the MP Main Menu prompt (MP>), enter cm. 2. From the MP Command Menu prompt (MP:CM>), enter lc (for LAN configuration). The default values display, and a prompt to modify the default values displays. Write down the information for future use. NOTE: If the Command Menu is not shown, enter q to return to the MP Main Menu, and enter cm. 3. Enter lc and press the Return key. The following screen displays: 58 Cabling and Powering the Server

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
•
When power is first applied. The BPS LEDs flash amber.
•
After 30 seconds has elapsed. The flashing amber BPS LED for each BPS becomes a
flashing green LED.
To interpret LED indicators, see the power cord policies.
3.
Log in to the MP:
a.
Enter
Admin
at the login prompt. The login is case sensitive.
It takes a few moments for the MP prompt to display. If it does not display, verify the
laptop serial device settings are correct:
8 bits, no parity, 9600 baud, and na for both Receive and Transmit. Then, try again.
b.
Enter
Admin
at the password prompt. The password is case sensitive.
The MP Main Menu is displayed:
Figure 4-7 MP Main Menu
Configuring LAN Information For the MP
To set the MP LAN IP address, follow these steps:
1.
At the MP Main Menu prompt (
MP>
), enter
cm
.
2.
From the MP Command Menu prompt (
MP:CM>
), enter
lc
(for LAN configuration).
The default values display, and a prompt to modify the default values displays.
Write down the information for future use.
NOTE:
If the Command Menu is not shown, enter
q
to return to the MP Main Menu, and
enter
cm
.
3.
Enter
lc
and press the
Return
key.
The following screen displays:
58
Cabling and Powering the Server