HP Server rp7420 HP 9000 rp7420 Server - User Service Guide, Fifth Edition - Page 77

PCI-X Hot-Plug LED OL* LEDs, Disk Drive LEDs, LAN Default Parameters

Get HP Server rp7420 PDF manuals and user guides View all HP Server rp7420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Table 5-8 Core I/O Buttons Button Identification (as Location silk-screened on the bulkhead) Function MP RESET Center of the core I/O card Resets the MP NOTE: If the MP RESET button is held for longer than five seconds, it clears the MP password and reset the LAN, RS-232 (serial port), and modem port parameters to their default values. LAN Default Parameters • IP Address-192.168.1.1 • Subnet mask-255.255.255.0 • Default gateway-192.168.1.1 • Hostname-gsp0 RS-232 (Serial Port) Default Parameters • 9600 baud • 8 bits • No parity Remote/Modem Port Parameters • Disabled OLR (Symbol next to Top end of the core I/O card Request OL* for this core I/O slot button is shown below) NOTE: The OLR function is not enabled for the core I/O card. PCI-X Hot-Plug LED OL* LEDs Table 5-9 OL* LED States State Normal operation, slot power on Slot selected, slot power on Slot needs attention, slot power on Slot available, slot power off Ready for OL*, slot power off Fault detected, slot power off Slot powering off or on Power (Green) On On On Off Off Off Flashing Disk Drive LEDs There are two tri-color LED on each disk drive. Attention (Yellow) Off Flashing On Off Flashing On Off LED Indicators 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Table 5-8 Core I/O Buttons
Function
Location
Button Identification (as
silk-screened on the
bulkhead)
Resets the MP
NOTE:
If the MP RESET button is held for longer than five
seconds, it clears the MP password and reset the LAN, RS-232
(serial port), and modem port parameters to their default
values.
LAN Default Parameters
•
IP Address—192.168.1.1
•
Subnet mask—255.255.255.0
•
Default gateway—192.168.1.1
•
Hostname—gsp0
RS-232 (Serial Port) Default Parameters
•
9600 baud
•
8 bits
•
No parity
Remote/Modem Port Parameters
•
Disabled
Center of the core I/O card
MP RESET
Request OL* for this core I/O slot
NOTE:
The OLR function is not enabled for the core I/O card.
Top end of the core I/O card
OLR (Symbol next to
button is shown below)
PCI-X Hot-Plug LED OL* LEDs
Table 5-9 OL* LED States
Attention (Yellow)
Power (Green)
State
Off
On
Normal operation, slot power on
Flashing
On
Slot selected, slot power on
On
On
Slot needs attention, slot power on
Off
Off
Slot available, slot power off
Flashing
Off
Ready for OL*, slot power off
On
Off
Fault detected, slot power off
Off
Flashing
Slot powering off or on
Disk Drive LEDs
There are two tri-color LED on each disk drive.
LED Indicators
77