HP Server rp7420 HP 9000 rp7420 Server - User Service Guide, Fifth Edition - Page 99

Replacing a BPS, Removing and Replacing a PCI Power Module, Extraction Levers, CAUTION

Get HP Server rp7420 PDF manuals and user guides View all HP Server rp7420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Figure 6-18 Extraction Levers 3. Slide the BPS forward using the extractions levers to remove it from the chassis. CAUTION: Use caution when handling the BPS. A BPS weighs 18 lb. Replacing a BPS To replace a BPS, follow these steps: 1. Verify that the extraction levers are in the open position, then insert the BPS into the empty slot. The BPS easily slides into the chassis. 2. To properly seat the connection, use a slow, firm pressure. 3. Ensure the BPS has seated by closing the extraction levers. 4. Replace the front bezel. NOTE: A green BPS LED indicates the BPS is operational. Removing and Replacing a PCI Power Module The PCI power module is located in the front of the chassis. You must turn off system power to replace this CRU. See "Powering Off Hardware Components and Powering On the Server" (page 84). Removing and Replacing a PCI Power Module 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Figure 6-18 Extraction Levers
3.
Slide the BPS forward using the extractions levers to remove it from the chassis.
CAUTION:
Use caution when handling the BPS. A BPS weighs 18 lb.
Replacing a BPS
To replace a BPS, follow these steps:
1.
Verify that the extraction levers are in the open position, then insert the BPS into the empty
slot. The BPS easily slides into the chassis.
2.
To properly seat the connection, use a slow, firm pressure.
3.
Ensure the BPS has seated by closing the extraction levers.
4.
Replace the front bezel.
NOTE:
A green BPS LED indicates the BPS is operational.
Removing and Replacing a PCI Power Module
The PCI power module is located in the front of the chassis. You must turn off system power to
replace this CRU. See
“Powering Off Hardware Components and Powering On the Server”
(page 84)
.
Removing and Replacing a PCI Power Module
99