HP VS80 DLT VS80 Tape Drive User's Guide - Page 37
Windows NT frequently asked questions, setting up a windows NT server for tape backup
UPC - 613326404355
View all HP VS80 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
Windows NT frequently asked questions http://www.hp.com/support/tape may have a later version hp learning products data protection drivers FAQs windows NT netware unix - SCO unix - linux frequently asked questions setting up a windows NT server for tape backup with hp surestore tape drives contents of this section introduction native backup applications how do tape drivers work within a Windows NT environment? how do I know what drivers I am using at the moment, and what drivers do I need for running tape backups? how do I tell if my tape drives and drivers are correctly set up? are there any important points I need to be aware of when changing drivers in my system? why does my autoloader not work correctly with ISV Backup Software, or the Windows NT in-built backup applet? why do I get SCSI errors when using my tape drive? which HP SureStore tape drives are certified by Microsoft, ISV's and IHV's for use on Windows NT? how do I use the built-in Tape Backup applet provided by Microsoft? NTBackup quick reference guide This topic is available in English only introduction As with most software development cycles, the Windows NT® network server operating system has been subject to a number of major and minor version releases over time, resulting in a number of different versions of Windows NT now being in common use. This Frequently Asked Questions (FAQ) document discusses the use of tape drivers for the HP Surestore tape drive product range within the following environments: Windows NT 3.51 (which may be upgraded by the use of the Windows NT Service Pack 5). Windows NT 4.0 (which may be upgraded by the use of the Windows NT Service Pack 4). Both of these versions of Windows NT are shipped with an integral native driver called "4mmDAT.sys". However, Hewlett-Packard recommends that its own tape drivers should be used in all circumstance. These drivers are contained on the relevant HP Surestore CD-ROM. A full range of drivers for Windows NT 3.51, Windows NT 4.0 and Windows 2000 (NT 5.0) covering all relevant HP Surestore tape drives are included. For full details, see the NTReadme.txt file which is also on the HP Surestore CD-ROM. To check which drivers you are currently running, refer to the answer to the question "How do I know what drivers I am using at the moment, and what drivers do I need for running tape backups?" For further details on tape drivers in general, refer to the answer to the question "How do tape drivers work within a Windows NT environment?" It is clear that, irrespective of the operating system version or tape drive vendor, problems are sometimes experienced when users attempt to set up Windows NT systems to perform tape backups. This "Windows NT Tape Backup Frequently Asked Questions" document attempts to highlight and resolve issues relative to tape drive backup under the Windows NT environment. It is recommended that you read the whole of this FAQ document rather than just specific questions. Note - Symbios is now owned by LSI Logic. Windows NT® is a U.S. registered trademark of Microsoft Corp. Windows 2000 Hewlett-Packard also supplies certified drivers for use with the native backup application that ships with the Windows 2000 operating system. These drivers are contained on the relevant HP Surestore CD-ROM. The latest information in support of this operating system can be found at http://www.hp.com/go/connect native backup applications Microsoft ships a built-in backup application with Windows NT called NTBackup. NTBackup supports the backing up of data on local drives and mapped network drives, and allows full / incremental backup strategies & monitoring of the current job. It does not support Autoloaders. For further details, refer to the answer to the question "How do I use the built-in Tape Backup applet provided by Microsoft?" Note - Ultrium high performance tape drives: As a general rule, native backup applications (such as NTBackup and tar) do not provide the required data streaming rate to get the full performance of your Ultrium drive. We recommend using a backup application, which provides better memory management as well as other useful features, such as TapeAlert. HP, Computer Associates, Veritas, Legato and Yosemite all provide suitable products that have been tested with your Ultrium drives. For the latest list of backup packages that support your Ultrium drives, please contact your tape drive or library manufacturer. first question Go to the first question "How do tape drivers work within a Windows NT environment?" © 1999-2001, Hewlett-Packard Company file:///C|/Documents%20and%20Settings/topher.COL-SPRINGS/Desktop/dltvs80%20manual/document/common/drivers_faqs/eng/nt_home.htm [11/29/2001 8:34:40 AM]