HP Visualize b1000 hp Visualize b1000, c3000, c3600 workstations parts replace - Page 5

Getting Started

Page 5 highlights

1 Getting Started The following important information must be adhered to for proper removal and replacement of all Hewlett-Packard parts. Safety Warnings WARNING Removing the device cover may expose sharp edges in the equipment chassis. To avoid injury, use care when installing customer add-on devices. NOTE Before performing removal/replacement procedures, position the workstation on a cushioned flat, stable surface, such as a table top or workbench. NOTE Installing the recommended HP replacement part in your B Class and C Class workstation does not affect the regulatory and safety classifications or approvals listed in the original owner's guide. Electrostatic Discharge (ESD) Precautions To prevent damage to the B Class and C Class workstation, observe all of the following ESD precautions while performing removal and replacement procedures: • Remove all ESD-generating materials from the work area in which you will remove and replace the workstation field replaceable unit(s). • Open the ESD materials provided with the replacement part kit. Unfold the black conductive sheeting (antistatic mat) and place it under a corner of the workstation. • Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to ground. Attach the static-grounding wrist strap by following the instructions on the package. Attach the sticky end of the wrist strap to bare metal on the rear panel of the workstation. • Connect all equipment together, including the static-free mat, static strap, clips attached to the wrist strap, nodes, and peripheral units. • Keep uninstalled printed circuit boards in their protective antistatic bags. • Once you have removed printed circuit boards from their protective antistatic bags, handle the printed circuit boards by their edges only. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

5
1
Getting Started
The
following
important
information
must
be
adhered
to
for
proper
removal
and
replacement of all Hewlett-Packard parts.
Safety Warnings
WARNING
Removing the device cover may expose sharp edges in the equipment
chassis. To avoid injury, use care when installing customer add-on
devices.
NOTE
Before performing removal/replacement procedures, position the workstation
on a cushioned flat, stable surface, such as a table top or workbench.
NOTE
Installing the recommended HP replacement part in your B Class and C
Class workstation does not affect the regulatory and safety classifications or
approvals listed in the original owner’s guide.
Electrostatic Discharge (ESD) Precautions
To prevent damage to the B Class and C Class workstation, observe all of the following
ESD precautions while performing removal and replacement procedures:
Remove all ESD-generating materials from the work area in which you will remove and
replace the workstation field replaceable unit(s).
Open the ESD materials provided with the replacement part kit. Unfold the black
conductive sheeting (antistatic mat) and place it under a corner of the workstation.
Wear a static strap to ensure that any accumulated electrostatic charge is discharged
from your body to ground. Attach the static-grounding wrist strap by following the
instructions on the package. Attach the sticky end of the wrist strap to bare metal on
the rear panel of the workstation.
Connect all equipment together, including the static-free mat, static strap, clips
attached to the wrist strap, nodes, and peripheral units.
Keep uninstalled printed circuit boards in their protective antistatic bags.
Once you have removed printed circuit boards from their protective antistatic bags,
handle the printed circuit boards by their edges only.