HP Xw8200 LSI SCSI: Integrated RAID User's Guide (PCI plug-in and system board - Page 37

Configuration Utility Disables Selection of Disk

Get HP Xw8200 - Workstation - 1 GB RAM PDF manuals and user guides
UPC - 882780210455
View all HP Xw8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

4. Save the configuration by pressing Esc and following the on-screen instructions. This creates the IM volume and triggers an automatic resync. 3.3.3 Configuration Utility Disables Selection of Disk Problem: The configuration utility does not allow a disk to be selected for an IM volume. Solution: To determine why the disk cannot be selected, press F4 on the RAID Properties screen to display diagnostic codes for each disk under the Size column. Code definitions are as follows: 0 Good status 1 Could not get serial number from disk 2 Can't confirm that disk has SMART capability 3 Maximum disks already configured for volume 4 Inquiry data returned says disk does not support wide, qtags, disconnects, or sector size is not 512 bytes 5 User disabled qtags or Disconnects for disk on device properties screen 6 Partitions on disk exceed size that can be mirrored by an already selected secondary or hot spare disk 7 Disk is not large enough to mirror partitions contained on selected primary disk 8 Hot spare detected while no IM volume exists. Must delete hot spare and save that configuration 9 Disk partition uses some or all of the last 32 sectors of the disk (16 Kbytes). The last 32 sectors are required for IR (Integrated RAID) internal processing. 10 Disk has sector size other than 512 bytes 11 Device is not a compatible device type. Must be non-removable disk. 12 Hot Spare too small to mirror volume 13 Maximum disks already configured for volume Troubleshooting Version 1.0 Copyright © 2003 by LSI Logic Corporation. All rights reserved. 3-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Troubleshooting
3-15
Version 1.0
Copyright © 2003 by LSI Logic Corporation. All rights reserved.
4.
Save the configuration by pressing
Esc
and following the on-screen
instructions. This creates the IM volume and triggers an automatic
resync.
3.3.3
Configuration Utility Disables Selection of Disk
Problem:
The configuration utility does not allow a disk to be selected
for an IM volume.
Solution:
To determine why the disk cannot be selected, press
F4
on
the RAID Properties screen to display diagnostic codes for each disk
under the Size column. Code definitions are as follows:
0
Good status
1
Could not get serial number from disk
2
Can’t confirm that disk has SMART capability
3
Maximum disks already configured for volume
4
Inquiry data returned says disk does not support wide, qtags,
disconnects, or sector size is not 512 bytes
5
User disabled qtags or Disconnects for disk on device properties
screen
6
Partitions on disk exceed size that can be mirrored by an already
selected secondary or hot spare disk
7
Disk is not large enough to mirror partitions contained on selected
primary disk
8
Hot spare detected while no IM volume exists. Must delete hot
spare and save that configuration
9
Disk partition uses some or all of the last 32 sectors of the disk
(16 Kbytes). The last 32 sectors are required for IR (Integrated
RAID) internal processing.
10
Disk has sector size other than 512 bytes
11
Device is not a compatible device type. Must be non-removable
disk.
12
Hot Spare too small to mirror volume
13
Maximum disks already configured for volume