HP Xw8200 LSI SCSI: Integrated RAID User's Guide (PCI plug-in and system board - Page 52

RAID Properties Screen: One IS Volume Con d, <Next Array&gt, <Delete Array&gt

Get HP Xw8200 - Workstation - 1 GB RAM PDF manuals and user guides
UPC - 882780210455
View all HP Xw8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Figure 5.5 RAID Properties Screen: One IS Volume Configured LSI Logic MPT SCSI Setup Utility Version MPTBIOS-IS-X.XX.XX RAID Properties Array:IS SCSI ID:0 Size(MB):25800 SCSI ID 0 1 2 Device Identifier Seagate xxxxxxxxx Seagate xxxxxxxxx Seagate xxxxxxxxx Array Disk? [Yes] [Yes] [Yes] Status OK OK OK Predict Failure NO NO NO Size (MB) 8683 8683 8683 Esc=Abort/Exit Arrow Keys=Select Item Home/End=Select Item -/+ = Change [Item] Enter=Execute F4=Diagnostic The RAID Properties screen shows information about one IS volume at a time. Only one volume can be active at a time. Here is an explanation of the menu options on the screen in Figure 5.5. • Select to display the next array (IS volume) on the same SCSI channel. Note: Although you cannot directly configure a second IS volume on the same SCSI channel or Fusion-MPT controller, you could take the member disks of a volume from another controller and connect them to this controller. Then the firmware would detect two IS volumes on the same controller. • Select to delete the IS volume currently displayed on the screen. The member disks will be converted back to standalone disks. • Select to make this IS volume the active array (volume) on the system. Activating an array deactivates all other arrays on the Fusion-MPT controller. 5-8 Setting Up Integrated Striping Version 1.0 Copyright © 2003 by LSI Logic Corporation. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
5-8
Setting Up Integrated Striping
Version 1.0
Copyright © 2003 by LSI Logic Corporation. All rights reserved.
Figure 5.5
RAID Properties Screen: One IS Volume Configured
The RAID Properties screen shows information about one IS volume at
a time. Only one volume can be
active
at a time. Here is an explanation
of the menu options on the screen in
Figure 5.5
.
•
Select
<Next Array>
to display the next array (IS volume) on the
same SCSI channel.
Note:
Although you cannot directly configure a second IS volume
on the same SCSI channel or Fusion-MPT controller, you
could take the member disks of a volume from another con-
troller and connect them to this controller. Then the firm-
ware would detect two IS volumes on the same controller.
•
Select
<Delete Array>
to delete the IS volume currently displayed
on the screen. The member disks will be converted back to stand-
alone disks.
•
Select
<Activate Array>
to make this IS volume the
active
array
(volume) on the system. Activating an array deactivates all other
arrays on the Fusion-MPT controller.
LSI Logic MPT SCSI Setup Utility Version MPTBIOS-IS-X.XX.XX
<Next Array>
<Delete Array>
<Activate Array>
RAID Properties
Array:IS SCSI ID:0
Size(MB):25800
SCSI
ID
Device Identifier
Array
Disk?
Status
Predict
Failure
Size
(MB)
0
Seagate xxxxxxxxx
[Yes]
OK
NO
8683
1
Seagate xxxxxxxxx
[Yes]
OK
NO
8683
2
Seagate xxxxxxxxx
[Yes]
OK
NO
8683
Esc=Abort/Exit
Arrow Keys=Select Item
-/+ = Change [Item]
Home/End=Select Item
Enter=Execute <Item>
F4=Diagnostic