HP Z210 HP Z210 Workstation Series User Guide - Page 52

Installing hard disk drives, HDD configuration - cmt specification

Get HP Z210 PDF manuals and user guides View all HP Z210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

9 Installing hard disk drives This section describes how to install a hard disk drive (HDD) in the workstation. HDD configuration The following table contains hard disk drive installation configuration information. Z210 CMT Z210 SFF HDD bays are designed to permit easy installation. Data cables are pre-connected in the workstation based on the factory configuration delivered. The workstation typically ships with an HDD, but additional drives can be added to expand data storage: ● Refer to the service label on the side access panel of your workstation to determine the location of the SATA Gen 3 (6 Gbit/sec) and Gen 2 (3 Gbit/sec) ports. ● Additional HDDs must be added in a specific sequence, depending on the type of workstation. ● Once installed, the HDDs are assigned drive letters, with C:\ being the typical boot disk. Drive letters are assigned using the Computer Setup (F10) Utility. ● With additional HDDs installed, the workstation boot sequence can be modified so that the workstation boots from one of the additional drives. Boot sequence is specified using the Computer Setup (F10) Utility. With additional HDDs installed, you have hard disk space for additional programs, data files, and backup. Refer to the workstation Maintenance and Service Guide at http://www.hp.com/support/workstation_manuals to learn how many HDDs the workstation can accommodate, drive installation order, and boot sequencing procedures. 44 Chapter 9 Installing hard disk drives ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
9
Installing hard disk drives
This section describes how to install a hard disk drive (HDD) in the workstation.
HDD configuration
The following table contains hard disk drive installation configuration information.
Z210 CMT
Z210 SFF
HDD bays are designed to permit easy installation. Data cables are pre-connected in the workstation based on the factory
configuration delivered.
The workstation typically ships with an HDD, but additional drives can be added to expand data storage:
●
Refer to the service label on the side access panel of your workstation to determine the location of the SATA Gen 3 (6
Gbit/sec) and Gen 2 (3 Gbit/sec) ports.
●
Additional HDDs must be added in a specific sequence, depending on the type of workstation.
●
Once installed, the HDDs are assigned drive letters, with C:\ being the typical boot disk. Drive letters are assigned using
the Computer Setup (F10) Utility.
●
With additional HDDs installed, the workstation boot sequence can be modified so that the workstation boots from one of
the additional drives. Boot sequence is specified using the Computer Setup (F10) Utility.
With additional HDDs installed, you have hard disk space for additional programs, data files, and backup.
Refer to the workstation
Maintenance and Service Guide
at
support/workstation_manuals
to learn how
many HDDs the workstation can accommodate, drive installation order, and boot sequencing procedures.
44
Chapter 9
Installing hard disk drives
ENWW