HP Z800 HP Z800 Workstation Maintenance and Service Guide - Page 109

Installing an optical disk drive in the optical drive bay,

Get HP Z800 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962082454
View all HP Z800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Installing an optical disk drive in the optical drive bay 1. Disconnect power from the workstation (see Predisassembly procedures on page 74). 2. Remove the side access panel (see Removing the side access panel on page 76). 3. Remove the airflow guide (see Removing the airflow guide on page 77). 4. If you are adding an additional drive, remove the filler tray (see Removing a filler tray on page 92). NOTE: Unused optical bay power cables are stored in this tray. 5. Lift and hold the drive release latch at the green touch point while sliding the optical disk drive into the bay 2. When the front of the drive is near its final position, release the latch, but continue to slide the drive inward until the latch closes and engages the drive. TIP: An optical drive longer than 175 mm (but less than 206 mm) must be installed in the middle or bottom bay. Figure 5-26 Installing the optical disk drive TIP: During installation the adjacent drive or filler may move slightly. You might have to slide and align both devices to get the release latch to close and engage both devices. ENWW Removing and installing components 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
Installing an optical disk drive in the optical drive bay
1.
Disconnect power from the workstation (see
Predisassembly procedures
on page
74
).
2.
Remove the side access panel (see
Removing the side access panel
on page
76
).
3.
Remove the airflow guide (see
Removing the airflow guide
on page
77
).
4.
If you are adding an additional drive, remove the filler tray (see
Removing a filler tray
on page
92
).
NOTE:
Unused optical bay power cables are stored in this tray.
5.
Lift and hold the drive release latch at the green touch point
while sliding the optical disk drive
into the bay
2
. When the front of the drive is near its final position, release the latch, but continue
to slide the drive inward until the latch closes and engages the drive.
TIP:
An optical drive longer than 175 mm (but less than 206 mm) must be installed in the middle
or bottom bay.
Figure 5-26
Installing the optical disk drive
TIP:
During installation the adjacent drive or filler may move slightly. You might have to slide and
align both devices to get the release latch to close and engage both devices.
ENWW
Removing and installing components
97