HP Z800 HP Z800 Workstation Maintenance and Service Guide - Page 121
Installing a hard disk drive, touch point and rotate the handle outward
UPC - 884962082454
View all HP Z800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 121 highlights
Installing a hard disk drive 1. Disconnect power from the workstation (see Predisassembly procedures on page 74). 2. Remove the side access panel (see Removing the side access panel on page 76). 3. Select the proper drive bay (SATA or SAS) in which to install the drive. Use the hard disk drive installation order shown in the following figure. Figure 5-41 Selecting a drive bay 4. If there is a drive carrier in the drive slot, press the hard drive carrier release latch at the green touch point and rotate the handle outward . Pull the drive carrier out of the hard drive bay as shown in the following figure 2. Figure 5-42 Removing the drive carrier from the chassis ENWW Removing and installing components 109
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
Installing a hard disk drive
1.
Disconnect power from the workstation (see
Predisassembly procedures
on page
74
).
2.
Remove the side access panel (see
Removing the side access panel
on page
76
).
3.
Select the proper drive bay (SATA or SAS) in which to install the drive. Use the hard disk drive
installation order shown in the following figure.
Figure 5-41
Selecting a drive bay
4.
If there is a drive carrier in the drive slot, press the hard drive carrier release latch at the green
touch point and rotate the handle outward
. Pull the drive carrier out of the hard drive bay as
shown in the following figure
2
.
Figure 5-42
Removing the drive carrier from the chassis
ENWW
Removing and installing components
109