HP Z800 HP Z800 Workstation Maintenance and Service Guide - Page 119

Removing a hard disk drive from the hard drive bay,

Get HP Z800 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962082454
View all HP Z800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Removing a hard disk drive from the hard drive bay 1. Disconnect power from the workstation (see Predisassembly procedures on page 74). 2. Remove the side access panel (see Removing the side access panel on page 76). 3. Press the hard drive carrier release latch at the green touch point and rotate the handle outward . Pull the drive carrier out of the hard drive bay as shown in the following figure 2. Figure 5-39 Removing the drive carrier from the chassis 4. Carefully separate the upper hard drive carrier rails, and then tilt the drive outward 2 as shown in the following figure. Figure 5-40 Removing the drive from the carrier Carefully separate the lower carrier rails , and then remove the drive from the carrier. ENWW Removing and installing components 107

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
Removing a hard disk drive from the hard drive bay
1.
Disconnect power from the workstation (see
Predisassembly procedures
on page
74
).
2.
Remove the side access panel (see
Removing the side access panel
on page
76
).
3.
Press the hard drive carrier release latch at the green touch point and rotate the handle outward
. Pull the drive carrier out of the hard drive bay as shown in the following figure
2
.
Figure 5-39
Removing the drive carrier from the chassis
4.
Carefully separate the upper hard drive carrier rails,
and then tilt the drive outward
2
as shown
in the following figure.
Figure 5-40
Removing the drive from the carrier
Carefully separate the lower carrier rails
, and then remove the drive from the carrier.
ENWW
Removing and installing components
107