HP Z800 HP Z800 Workstation Maintenance and Service Guide - Page 134

Installing a hard disk drive in the optical drive bay,

Get HP Z800 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962082454
View all HP Z800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

Installing a hard disk drive in the optical drive bay TIP: For optimum performance, install the hard disk drive in the bottom bay; do not install it in the top bay. 1. Disconnect power from the workstation (see Predisassembly procedures on page 74). 2. Remove the side access panel (see Removing the side access panel on page 76). 3. Remove the airflow guide (see Removing the airflow guide on page 77). 4. Remove the expansion card support (see Removing the expansion card support on page 78). 5. Carefully separate the carrier rails and set the drive between them, aligning the pins with the drive mounting holes. Release the rails to secure the rails on the drive as shown in the following figure. Figure 5-63 Installing the carrier rails 6. Slide the drive into the carrier until it snaps into place as shown in the following figure. Figure 5-64 Installing the drive in the carrier 122 Chapter 5 Replacing components ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
Installing a hard disk drive in the optical drive bay
TIP:
For optimum performance, install the hard disk drive in the bottom bay; do not install it in the top
bay.
1.
Disconnect power from the workstation (see
Predisassembly procedures
on page
74
).
2.
Remove the side access panel (see
Removing the side access panel
on page
76
).
3.
Remove the airflow guide (see
Removing the airflow guide
on page
77
).
4.
Remove the expansion card support (see
Removing the expansion card support
on page
78
).
5.
Carefully separate the carrier rails and set the drive between them, aligning the pins with the drive
mounting holes.
Release the rails to secure the rails on the drive as shown in the following figure.
Figure 5-63
Installing the carrier rails
6.
Slide the drive into the carrier until it snaps into place as shown in the following figure.
Figure 5-64
Installing the drive in the carrier
122
Chapter 5
Replacing components
ENWW