Hikvision ERI-Q108-P8 User Manual - Page 146

Menu > Record > Parameters > Record

Get Hikvision ERI-Q108-P8 PDF manuals and user guides View all Hikvision ERI-Q108-P8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

ERI-Q10x-Px NVR User Manual 10. If the resource is not enough, end some unnecessary processes. 11. Check if the fault is solved by the above steps. 12. If it is solved, finish the process. If not, contact an engineer from our company for further processing. When using the NVR to get the live view audio, there is no sound or there is too much noise, or the volume is too low. Possible Reasons: • Cable between the pickup and IP camera is not connected well; impedance mismatches or incompatible. • The stream type is not set as "Video & Audio." • The encoding standard is not supported with NVR. 1. Verify the cable between the pickup and IP camera is connected well; impedance matches and compatible. 2. Log in the IP camera directly, and turn the audio on, check if the sound is normal. If not, contact the manufacturer of the IP camera. 3. Verify the setting parameters are correct. 4. Select Menu > Record > Parameters > Record and set the Stream Type to Audio & Video. 5. Verify the audio encoding standard of the IP camera is supported by the NVR. 6. NVR supports G722.1 and G711 standards, and if the encoding parameter of the input audio is not one of the previous two standards, you can log in the IP camera to configure it to the supported standard. 7. Check if the fault is solved by the above steps. 8. If it is solved, finish the process. If not, contact an engineer from our company for further processing. The image gets stuck when the NVR is playing back by single or multi-channel. Possible Reasons: • Poor network between NVR and IP camera, and there exists packet loss during the transmission. • The frame rate is not the real-time frame rate. • The NVR supports up to 16-channel synchronize playback at 4CIF resolution. If you want 16-channel synchronized playback at 720p resolution, frame extracting may occur, which leads to slight sticking. 1. Verify the network between NVR and IP camera is connected. 2. When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable. 3. Open the Super Terminal, and execute the command of "ping 192.168.0.0 -l 1472 -f" (the IP address may change according to the real condition), and check if there exists packet loss. UM ERI-Q10x-Px 030118NA 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
ERI-Q10x-Px NVR User Manual
UM ERI-Q10x-Px 030118NA
145
If the resource is not enough, end some unnecessary processes.
10.
Check if the fault is solved by the above steps.
11.
If it is solved, finish the process. If not, contact an engineer from our company for further processing.
12.
When using the NVR to get the live view audio, there is no sound or there is too much noise, or the volume
is too low.
Possible Reasons:
•
Cable between the pickup and IP camera is not connected well; impedance mismatches or incompatible.
•
The stream type is not set as “Video & Audio.”
•
The encoding standard is not supported with NVR.
Verify the cable between the pickup and IP camera is connected well; impedance matches and compatible.
1.
Log in the IP camera directly, and turn the audio on, check if the sound is normal. If not, contact the
2.
manufacturer of the IP camera.
Verify the setting parameters are correct.
3.
Select
Menu > Record > Parameters > Record
and set the Stream Type to Audio & Video.
4.
Verify the audio encoding standard of the IP camera is supported by the NVR.
5.
NVR supports G722.1 and G711 standards, and if the encoding parameter of the input audio is not one of
6.
the previous two standards, you can log in the IP camera to configure it to the supported standard.
Check if the fault is solved by the above steps.
7.
If it is solved, finish the process. If not, contact an engineer from our company for further processing.
8.
The image gets stuck when the NVR is playing back by single or multi-channel.
Possible Reasons:
•
Poor network between NVR and IP camera, and there exists packet loss during the transmission.
•
The frame rate is not the real-time frame rate.
•
The NVR supports up to 16-channel synchronize playback at 4CIF resolution. If you want 16-channel
synchronized playback at 720p resolution, frame extracting may occur, which leads to slight sticking.
Verify the network between NVR and IP camera is connected.
1.
When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable.
2.
Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address may
3.
change according to the real condition), and check if there exists packet loss.