IBM 17011RS Maintenance Manual - Page 68

approximately

Get IBM 17011RS - TotalStorage DS300 Model NAS Server PDF manuals and user guides
UPC - 000435304971
View all IBM 17011RS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

c. While squeezing together the latch and lever, push both latches up as far as they will go. The power supply will slide the rest of the way into the bay. 7. Connect the power cord to the power supply. 8. Untwist the power cord strain-relief plastic tie (located below and to the right of the ac power switch). 9. Wrap the strain-relief tie around the power cord approximately 10 cm (4 in.) from the ac power connector end; then, twist the tie. 10. Connect the power-supply cord into a properly grounded electrical outlet. Note: The fault (amber) LED is lit on the new power supply because its power switch is turned off. 11. Turn on the power supply. After you turn on the power, the fault (amber) LED is off and the Power OK (green) LEDs are lit. 54 IBM TotalStorage DS300 and DS400: Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
c.
While
squeezing
together
the
latch
and
lever,
push
both
latches
up
as
far
as
they
will
go.
The
power
supply
will
slide
the
rest
of
the
way
into
the
bay.
7.
Connect
the
power
cord
to
the
power
supply.
8.
Untwist
the
power
cord
strain-relief
plastic
tie
(located
below
and
to
the
right
of
the
ac
power
switch).
9.
Wrap
the
strain-relief
tie
around
the
power
cord
approximately
10
cm
(4
in.)
from
the
ac
power
connector
end;
then,
twist
the
tie.
10.
Connect
the
power-supply
cord
into
a
properly
grounded
electrical
outlet.
Note:
The
fault
(amber)
LED
is
lit
on
the
new
power
supply
because
its
power
switch
is
turned
off.
11.
Turn
on
the
power
supply.
After
you
turn
on
the
power,
the
fault
(amber)
LED
is
off
and
the
Power
OK
(green)
LEDs
are
lit.
54
IBM
TotalStorage
DS300
and
DS400:
Hardware
Maintenance
Manual