Intermec CV41 CV41 Vehicle Mount Computer (Windows CE) User Guide - Page 102

Install Switch for Screen Blanking, Enable Screen Blanking, Device Settings > Screen Blanking

Get Intermec CV41 PDF manuals and user guides View all Intermec CV41 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Chapter 7 - Enable Screen Blanking Install Switch for Screen Blanking This section explains how mount, connect, and enable the switch for screen blanking. 1 Using your own mounting hardware, secure the switch sensor to the vehicle. 2 Connect the serial cable to the switch. Make sure that Pin 7 connects to the switch connection and Pin 8 connects to the other terminal. Pin 8 Pin 7 3 Connect the serial cable to the COM1 or COM2 port on your computer. Enable Screen Blanking After you have wired and mounted the motion switch sensor, you must enable screen blanking in Intermec settings on the vehicle mount computer. 1 In Intermec Settings, select Device Settings > Screen Blanking on Motion. 2 In Screen Blanking on Motion, select the COM port the custom serial cable is connected to. 3 In Screen-on delay after motion stops (sec), enter the amount of time in seconds that you want the display to turn on after the vehicle is stationary. 4 Tap OK. Screen blanking is enabled. 88 CV41 Vehicle Mount Computer (Windows CE) User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
Chapter 7 — Enable Screen Blanking
88
CV41 Vehicle Mount Computer (Windows CE) User Guide
Install Switch for Screen Blanking
This section explains how mount, connect, and enable the switch for
screen blanking.
1
Using your own mounting hardware, secure the switch sensor to
the vehicle.
2
Connect the serial cable to the switch. Make sure that Pin 7 connects to
the switch connection and Pin 8 connects to the other terminal.
3
Connect the serial cable to the COM1 or COM2 port on your computer.
Enable Screen Blanking
After you have wired and mounted the motion switch sensor, you must
enable screen blanking in Intermec settings on the vehicle mount
computer.
1
In Intermec Settings, select
Device Settings > Screen Blanking on
Motion
.
2
In
Screen Blanking on Motion
, select the COM port the custom
serial cable is connected to.
3
In
Screen-on delay after motion stops (sec)
, enter the amount of
time in seconds that you want the display to turn on after the
vehicle is stationary.
4
Tap
OK
. Screen blanking is enabled.
Pin 8
Pin 7