Intermec PC23d PC23 and PC43 Desktop Printer User Manual - Page 78

Calculate RFID Tag Position, Wizard > Calibration > RFID, Calibration, Enable

Get Intermec PC23d PDF manuals and user guides View all Intermec PC23d manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Chapter 2 - Set Up the Printer 1 Make sure the media type and media length are properly configured. 2 From the Main Menu, select Wizard > Calibration > RFID Calibration. 3 To enable the RFID module, select Enable. 4 Load the RFID media. 5 Select OK. When the calibration is complete, the printer displays the RFID Tag Position and Output Power (UHF inlays, only). Calculate RFID Tag Position You can perform a manual calculation to come up with an estimate of the RFID Tag Position. Because this value is an estimate, you may need to slightly adjust the calculated value to achieve the best results. 1 Make sure Start Adjust and Stop Adjust are set to 0. 2 Measure the yChip value, which is the distance between the RFID chip and the media edge aligned with the tear bar. -BCFMUPQ PGGPSN .FEJBFEHF BMJHOFEXJUI UFBSCBS /FYUMBCFM 3'*%DIJQ Z$IJQ 64 PC23 and PC43 Desktop Printer User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
Chapter 2 — Set Up the Printer
64
PC23 and PC43 Desktop Printer User Manual
1
Make sure the media type and media length are properly
configured.
2
From the Main Menu, select
Wizard > Calibration > RFID
Calibration
.
3
To enable the RFID module, select
Enable
.
4
Load the RFID media.
5
Select
OK
.
When the calibration is complete, the printer displays the RFID
Tag Position and Output Power (UHF inlays, only).
Calculate RFID Tag Position
You can perform a manual calculation to come up with an estimate of
the RFID Tag Position. Because this value is an estimate, you may need
to slightly adjust the calculated value to achieve the best results.
1
Make sure Start Adjust and Stop Adjust are set to 0.
2
Measure the yChip value, which is the distance between the RFID
chip and the media edge aligned with the tear bar.