Invacare MVPS Owners Manual - Page 48

Adjusting T-arm Depth Adjusting T-arm Depth, Desk Length Arms,

Get Invacare MVPS PDF manuals and user guides View all Invacare MVPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

SECTION 6 ARMS ADJUSTING T-ARM DEPTH (FIGURE 8) 1. Remove the two (2) phillips screws that secure the arm pad to the arm tube. 2. Remove the two (2) socket screws that secure the arm tube to the T-arm post. 3. Reposition the arm tube on the T-arm post: A. Desk Length Arms - to one (1) of three (3) positions depending on the desired arm pad depth. B. Full Length Arms - to one (1) of five (5) positions depending on the desired arm pad depth. NOTE: Additional positions are obtainable by turning the arm tube 180o. 4. Re-secure the arm tube to the T-arm post with the two (2) socket screws. Torque to 6070 in./lbs. 5. Reattach the arm pad to the arm tube with the two (2) phillips screws. Tighten securely. 6. Repeat for the opposite side, if necessary. ARMS NOTE: Desk length arm shown for clarity. Arm Pad Socket Screws Phillips Screw Arm Tube NOTE: If necessary, turn arm tube 180o to obtain two (2) positions. T-Arm Post Phillips Screw FIGURE 8 - ADJUSTING T-ARM DEPTH ADJUSTING T-ARM SOCKETS (FIGURE 9) 1. Remove the rear wheels from the wheelchair, if necessary. Refer to REMOVING/INSTALLING REAR WHEELS in SECTION 7 of this manual. 2. Loosen, but do not remove the four (4) hex screws and washers that secure T-arm socket to T- arm clamp. NOTE: The T-arm socket will disassemble if the four (4) hex screws and washers are removed. 3. Slide the T-arm into the T-arm socket until the locking lever is in the slot in the T-arm socket and an audible "click" is heard. 4. Squeeze the T-arm socket the T-arm clamp together until the socket is flush with the T-arm. 5. While holding the T-arm socket and the T-arm clamp together, tighten the four (4) hex screws and washers. Torque to 80-90 in./lbs. 6. Press in on the locking lever and lift the T-arm straight up and out of the T-arm socket. 7. Repeat STEPS 3-6, if necessary until the T-arm slides in the T-arm socket as desired. 8. If necessary, install rear wheels. Refer to REMOVING/INSTALLING REAR WHEELS in SECTION 7 of this manual. MVP™ & MVP jr.™ 48 Part No. 1106638

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
MVP± & MVP jr²±
48
Part No² 1106638
Socket Screws
Arm Pad
Phillips
Screw
T-Arm Post
Arm Tube
NOTE: If neces-
sary, turn arm
tube 180
o
to
obtain two (2)
positions±
Phillips Screw
FIGURE 8 - ADJUSTING T-ARM DEPTH
ADJUSTING T-ARM DEPTH (FIGURE 8)
1±
Remove the two (2) phillips screws that secure the arm pad to the arm tube±
2±
Remove the two (2) socket screws that secure the arm tube to the T-arm post±
3±
Reposition the arm tube on the T-arm post:
A±
Desk Length Arms
- to one (1) of three (3) positions depending on the desired
arm pad depth±
B±
Full Length Arms
- to one (1) of five (5) positions depending on the desired arm
pad depth±
NOTE: Additional positions are obtainable by turning the arm tube 180
o
±
4±
Re-secure the arm tube to the T-arm post with the two (2) socket screws± Torque to 60-
70 in±/lbs±
5±
Reattach the arm pad to the arm tube with the two (2) phillips screws± Tighten securely±
6±
Repeat for the opposite side, if necessary±
ADJUSTING T-ARM SOCKETS (FIGURE 9)
1±
Remove the rear wheels from the wheelchair, if necessary± Refer to
REMOVING/INSTALL-
ING
REAR WHEELS in SECTION 7 of this manual±
2±
Loosen, but do not remove the four (4) hex screws and washers that secure T-arm socket to
T- arm clamp±
NOTE: The T-arm socket will disassemble if the four (4) hex screws and washers are removed±
3±
Slide the T-arm into the T-arm socket until the locking lever is in the slot in the T-arm socket
and an audible "click" is heard±
4±
Squeeze the T-arm socket the T-arm clamp together until the socket is flush with the T-arm±
5±
While holding the T-arm socket and the T-arm clamp together, tighten the four (4) hex
screws and washers± Torque to 80-90 in±/lbs±
6±
Press in on the locking lever and lift the T-arm straight up and out of the T-arm socket±
7±
Repeat STEPS 3-6, if necessary until the T-arm slides in the T-arm socket as desired±
8±
If necessary, install rear wheels± Refer to
REMOVING/INSTALLING
REAR WHEELS in
SECTION 7 of this manual±
SECTION 6
ARMS
ARMS
NOTE: Desk length arm
shown for clarity±