Kenmore 8075 Use and Care Manual - Page 12

wire, cut bare wire even with outer covering.

Get Kenmore 8075 - 24 in. Laundry Center PDF manuals and user guides View all Kenmore 8075 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3. Move the green painted screw from the internal to the external ground location. Connect ground wire (green or bare) of power supply cable to external ground conductor screw. Tighten screw. B 1. Loosen or remove center, silver-colored terminal block screw. 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw. B ...... C C E A. Neutral wire (white or center wire) B. Center silver-colored terminal block screw C. Neutral ground wire D. External ground conductor screw E. Ground wire (green or bare) of power supply cable F Internal ground conductor location G. 3/4"(!.9 cm) UL listed, strain relief 4. Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 3-wire connection: Power supply cord Use where local codes permit connecting cabinet-ground conductor to neutral wire. C G F A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Ground prong D. Spade terminals with up turned ends EL _" (1.9 cm) UL listed strain relief E Ring terminals G. Neutral (white or center wire) D A. Neutral wire (white or center wire) B. Center silver-colored terminal block screw C. Neutral ground wire D. Internal ground conductor screw E.3/4"(1.9 cm) UL listed, strain relief 3. Connect the other wires to outer terminal block screws. Tighten screws. 4. Tighten strain relief screws. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. Now go to "Venting Requirements." 3-wire connection: Direct Wire Use where local codes permit connecting cabinet-ground conductor to neutral wire. Direct wire cable must have 5 ft (1.52 m) of extra length so laundry center can be moved if needed. Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape. When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
3.
Move the green painted
screw from the internal to the
1.
external ground
location.
Connect
ground
wire (green or bare)
2.
of power supply
cable to external ground
conductor
screw.
Tighten
screw.
B
4.
E
......
C
A. Neutral
wire (white or center wire)
B. Center silver-colored
terminal
block screw
C. Neutral
ground
wire
D. External ground
conductor
screw
E. Ground
wire (green or bare) of power
supply
cable
F
Internal ground
conductor
location
G.
3/4"
(!.9
cm) UL listed,
strain
relief
Place the hooked ends of the other power supply
cable wires
under the outer terminal
block screws
(hooks facing right).
Squeeze
hooked ends together.
Tighten
screws.
5.
Tighten
strain relief screw.
6.
Insert tab of terminal
block cover into slot of dryer rear panel.
Secure cover with
hold-down
screw.
7.
You have completed
your electrical
connection.
Now go to
"Venting
Requirements."
3-wire
connection:
Power
supply
cord
Use where
local codes permit
connecting
cabinet-ground
conductor
to neutral wire.
C
G
F
A. 3-wire
receptacle
(NEMA type
10-30R)
B. 3-wire plug
C. Ground prong
D. Spade
terminals
with up turned
ends
EL
_"
(1.9 cm) UL listed
strain
relief
E Ring terminals
G. Neutral
(white or center wire)
Loosen or remove center, silver-colored
terminal
block screw.
Connect
neutral wire (white or center wire) of power
supply
cord to the center, silver-colored
terminal
screw of the
terminal
block. Tighten
screw.
B
C
D
A. Neutral wire (white or center wire)
B. Center silver-colored terminal block
screw
C. Neutral ground wire
D. Internal ground conductor screw
E.3/4"(1.9 cm) UL listed,
strain
relief
3.
Connect
the other wires to outer terminal
block
screws.
Tighten screws.
4.
Tighten strain relief screws.
5.
Insert tab of terminal
block cover into slot of dryer rear panel.
Secure cover with
hold-down
screw.
6.
You have completed
your electrical
connection.
Now go to
"Venting
Requirements."
3-wire
connection:
Direct
Wire
Use where
local codes permit
connecting
cabinet-ground
conductor
to neutral wire.
Direct wire cable must have 5 ft (1.52 m) of extra length so
laundry center can be moved
if needed.
Strip 31/2
'' (8.9 cm) of outer covering
from end of cable. Strip
insulation
back 1" (2.5 cm). If using 3-wire cable with
ground
wire, cut bare wire even with outer covering.
Shape
ends of wires
into a hook shape.
When connecting
to the terminal
block,
place the hooked
end of
the wire under the screw of the terminal
block (hook facing right),
squeeze hooked
end together
and tighten
screw.
12