Kyocera ECOSYS FS-1370DN FS-1370DN Operation Guide (Advanced) - Page 72

>>Sleep Timer, Sleep Timer Sleep timer timeout time

Get Kyocera ECOSYS FS-1370DN PDF manuals and user guides View all Kyocera ECOSYS FS-1370DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

>>Sleep Timer 015 min. Sleep Timer (Sleep timer timeout time) You can adjust the length of time the printer waits before entering Auto Sleep in the absence of data. The printer reverts to normal operation mode when the printer receives a print job, the operation panel is operated, or one of the exterior covers is opened. The default time is 15 minutes. Note Calibration is automatically executed before the printer reverts to normal operation mode. 1 Press Z while >Timer > is displayed. 2 Press U or V repeatedly until >>Sleep Timer appears. 3 To change the timeout time, press [OK]. A blinking cursor (_) appears. 4 Press U or V to increase or decrease the value at the blinking cursor and set the desired time. The timer can be set between 1 and 240 minutes. Use Y and Z to move the cursor right and left. 5 Press [OK]. 6 Press [MENU]. The display returns to Ready. 2-54 Using the Operation Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
2-54
Using the Operation Panel
Sleep Timer (Sleep timer timeout time)
You can adjust the length of time the printer waits before entering Auto
Sleep in the absence of data.
The printer reverts to normal operation mode when the printer receives a
print job, the operation panel is operated, or one of the exterior covers is
opened. The default time is
15
minutes.
1
Press
Z
while
>Timer >
is displayed.
2
Press
U
or
V
repeatedly until
>>Sleep Timer
appears.
3
To change the timeout time, press
[OK]
. A blinking cursor (
_
)
appears.
4
Press
U
or
V
to increase or decrease the value at the blinking
cursor and set the desired time. The timer can be set between
1
and
240
minutes. Use
Y
and
Z
to move the cursor right and left.
5
Press
[OK]
.
6
Press
[MENU]
. The display returns to
Ready
.
Note
Calibration is automatically executed before the printer
reverts to normal operation mode.
>>Sleep Timer
015
min.