Lacie d2 Network 2 User Manual - Page 14

STEP 2: Connect the Ethernet Cable, Gigabit Ethernet Cables And Connectors

Get Lacie d2 Network 2 PDF manuals and user guides View all Lacie d2 Network 2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

LaCie d2 Network 2 • DESIGN BY NEIL POULTON User Manual 2.2. STEP 2: Connect the Ethernet Cable 1. Connect the Ethernet cable to the Ethernet port on the back of the LaCie d2 Network 2 (Fig. 04). 2. Connect the other end of the Ethernet cable into an available Ethernet "out" port on your router or hub (refer to your router or hub's documentation if necessary). 3. Turn on the drive by pressing the power button on the back of the drive (Fig. 05). The front LED will turn on and then begin blinking. The drive is ready to be accessed once the blue LED has stopped blinking. The product may take up to 3 minutes to boot. Now move on to step 3, section 2.3. STEP 3: Connect using LaCie Network Assistant. TECHNICAL NOTE: Depending on your computer's Ethernet settings, you may be able to connect the d2 Network 2 directly to your computer using the Ethernet cable. Fig. 04 Gigabit Ethernet Cables And Connectors See Fig. 06 for an illustration of the Ethernet cable used to connect your LaCie d2 Network 2 to your network device. The ends of the Ethernet cable are the same and either end can be connected to the LaCie d2 Network 2 or your router. Fig. 05 Connecting to a Network page 14 Fig. 06 - Gigabit Ethernet cable ends

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
LaCie d2 Network 2
• DESIGN BY NEIL POULTON
Connecting to a Network
User Manual
page 14
2.2. STEP 2: Connect the Ethernet
Cable
1. Connect the Ethernet cable to the Ethernet port on the back of
the LaCie d2 Network 2 (
Fig. 04
).
2. Connect the other end of the Ethernet cable into an available
Ethernet “out” port on your router or hub (refer to your router or
hub’s documentation if necessary).
3. Turn on the drive by pressing the power button on the back of
the drive (
Fig. 05
). The front LED will turn on and then begin
blinking.
The drive is ready to be accessed once the blue LED has stopped
blinking. The product may take up to 3 minutes to boot.
Now move on to step 3, section
2.3. STEP 3: Connect using LaCie
Network Assistant
.
TECHNICAL NOTE:
Depending on your computer’s Ethernet set-
tings, you may be able to connect the d2 Network 2 directly to your
computer using the Ethernet cable.
Gigabit Ethernet Cables And Connectors
See
Fig. 06
for an illustration of the Ethernet cable used to connect
your LaCie d2 Network 2 to your network device. The ends of the
Ethernet cable are the same and either end can be connected to the
LaCie d2 Network 2 or your router.
Fig. 05
Fig. 06 - Gigabit Ethernet cable ends
Fig. 04