Lantronix IntelliBox-I/O IntelliBox-I/O - User Guide - Page 69

Email on Disconnect

Get Lantronix IntelliBox-I/O PDF manuals and user guides View all Lantronix IntelliBox-I/O manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

7: Network, Serial Line, Tunnel, and Modbus Settings Tunnel - Connect Description Mode Page Settings Reconnect Timer Enter the maximum number of milliseconds to wait before trying to reconnect to the remote host after a previous attempt failed or the connection was closed. Default is 15000 milliseconds. Flush Serial Data Select whether to flush the serial line when a connection is made. Choices are: Enabled = flush the serial line when a connection is made. Disabled = do not flush the serial line. (default) SSH Username If you selected SSH as the protocol for this tunnel, enter the SSH client user that is to be used for the SSH connection. Default is . Block Serial Select whether incoming block serial data should be discarded. This setting is used for debugging purposes. Choices are: On = discard all incoming serial data on the respective interface. Off = do not discard all incoming serial data. (default) Block Network Select whether incoming block network data should be discarded. This setting is used for debugging purposes. Choices are: On = discard all incoming network data on the respective interface. Off = do not discard all incoming network data. (default) Email on Connect Select whether email should be sent when a connection is made. None = do not send an email. Email # = send an email corresponding to the tunnel number. Email on Disconnect Select whether email should be sent when a connection is closed. None = do not send an email. Email # = send an email corresponding to the tunnel number. Output Select Select the output to be closed while a connection is active. XI01 = Output from digital port 1 XI02 = Output from digital port 2 Relay = Output from the relay Mode Select whether the same output may also be closed by another condition, (e.g. Connect Mode settings from Tunnel 1 and Tunnel 2 for the same digital port.) Exclusive Control = The same output may not be closed by another condition. Logical-Or = The same output may be closed by another condition. IntelliBox-I/O 2100 User Guide 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
7: Network, Serial Line, Tunnel, and Modbus Settings
IntelliBox-I/O 2100 User Guide
69
Tunnel – Connect
Mode Page
Settings
Description
Reconnect Timer
Enter the maximum number of milliseconds to wait before trying to
reconnect to the remote host after a previous attempt failed or the
connection was closed. Default is 15000 milliseconds.
Flush Serial Data
Select whether to flush the serial line when a connection is made.
Choices are:
Enabled
= flush the serial line when a connection is made.
Disabled
= do not flush the serial line. (default)
SSH Username
If you selected SSH as the protocol for this tunnel, enter the SSH
client user that is to be used for the SSH connection. Default is
<none>.
Block Serial
Select whether incoming block serial data should be discarded. This
setting is used for debugging purposes. Choices are:
On
= discard all incoming serial data on the respective interface.
Off
= do not discard all incoming serial data. (default)
Block Network
Select whether incoming block network data should be discarded.
This setting is used for debugging purposes. Choices are:
On
= discard all incoming network data on the respective interface.
Off
= do not discard all incoming network data. (default)
Email on Connect
Select whether email should be sent when a connection is made.
None
= do not send an email.
Email #
= send an email corresponding to the tunnel number.
Email on Disconnect
Select whether email should be sent when a connection is closed.
None
= do not send an email.
Email #
= send an email corresponding to the tunnel number.
Output
Select
Select the output to be closed while a connection is active.
XI01 =
Output from digital port 1
XI02 =
Output from digital port 2
Relay
=
Output from the relay
Mode
Select whether the same output may also be closed by another
condition, (e.g. Connect Mode settings from Tunnel 1 and Tunnel 2
for the same digital port.)
Exclusive Control
= The same output may not be closed by another
condition.
Logical-Or
= The same output may be closed by another condition.