Lantronix XPress-DR-IAP XPress-DR / XPress-DR-IAP - User Guide - Page 96

Table 21 - Monitor Mode Commands, Table 22 -Command Response Codes, Function, Command

Get Lantronix XPress-DR-IAP PDF manuals and user guides View all Lantronix XPress-DR-IAP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Monitor Mode Table 21 - Monitor Mode Commands Command DL SF x.x.x.x VS x.x.x.x GC x.x.x.x SC x.x.x.x PI x.x.x.x AT TT NC RS SI xxx.xxx.xxx.xxx: yyy.yyy.yyy.yyy QU G0, G1, ....,Ge, Gf S0, S1,...,Se, Sf Command Name Download Send Firmware Version Get Configuration Send Configuration Ping ARP Table TCP Connection Table Network Connection Reset Send/Set IP Address Quit Get configuration from memory page Set configuration to memory page Function Download firmware to the Device Server via the serial port in hex format Send firmware to Device Server with IP address x.x.x.x Query software header record (16 bytes) of Device Server with IP address x.x.x.x Get configuration of Device Server with IP address x.x.x.x as hex records (120 bytes) Set configuration of Device Server with IP address x.x.x.x from hex records Ping Device Server with IP address x.x.x.x to check device status Show the Device Server's ARP table entries Shows all incoming and outgoing TCP connections Shows the Device Server's IP configuration Resets the Device Server's power Remotely assign an IP address to a Device Server, where xxx.xxx.xxx.xxx is the IP address, and yyyy.yyy.yyyy.yyy is the two-part identification number at the bottom of the label, converted to decimal, and written twice. Exit diagnostics mode Gets a memory page of configuration information from the device. Sets a memory page of configuration information on the device. Responses to some of the commands are given in Intel Hex format (see The Intel Hex Format on page 8-5). Note: You may be required to enter QU twice to exit monitor mode. Entering any of the commands listed above will generate one of the following command response codes: Table 22 -Command Response Codes Response 0> 1> 2> 8> 9> Meaning OK; no error No answer from remote device Cannot reach remote device or no answer Wrong parameter(s) Invalid command 7-2 DSTni-XPress DR User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Monitor Mode
Table 21 - Monitor Mode Commands
Function
DL
Download
Download firmware to the Device Server via the
serial port in hex format
SF x.x.x.x
Send Firmware
Send firmware to Device Server with IP address
x.x.x.x
Version
Query software header record (16 bytes) of
Device Server with IP address x.x.x.x
GC x.x.x.x
Get configuration of Device Server with IP
address x.x.x.x as hex records (120 bytes)
SC x.x.x.x
Send Configuration
Command
VS x.x.x.x
Get Configuration
Set configuration of Device Server with IP address
x.x.x.x from hex records
PI x.x.x.x
Ping
Ping Device Server with IP address x.x.x.x to
check device status
AT
ARP Table
Show the Device Server’s ARP table entries
TT
TCP Connection
Table
Shows all incoming and outgoing TCP
connections
NC
Network Connection
Shows the Device Server’s IP configuration
RS
Reset
Resets the Device Server’s power
SI
xxx.xxx.xxx.xxx:
yyy.yyy.yyy.yyy
Send/Set IP
Address
Remotely assign an IP address to a Device
Server, where xxx.xxx.xxx.xxx is the IP address,
and yyyy.yyy.yyyy.yyy is the two-part identification
number at the bottom of the label, converted to
decimal, and written twice.
QU
Quit
Exit diagnostics mode
G0, G1,
....
,Ge,
Gf
Get configuration
from memory page
Gets a memory page of configuration information
from the device.
S0, S1,...,Se, Sf
Set configuration to
memory page
Sets a memory page of configuration information
on the device.
Responses to some of the commands are given in Intel Hex format (see
The Intel Hex Format
on page
8-5
).
Note: You may be required to enter QU twice to exit monitor mode.
Entering any of the commands listed above will generate one of the following command
response codes:
Table 22 -Command Response Codes
Response
Meaning
0>
OK; no error
1>
No answer from remote device
2>
Cannot reach remote device or no answer
8>
Wrong parameter(s)
9>
Invalid command
7-2
DSTni-XPress DR User Guide