Maytag MED5800TW Technical Education - Page 68

Activating The Test Mode, Test Mode Functionality

Get Maytag MED5800TW - Electric Dryer PDF manuals and user guides View all Maytag MED5800TW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Activating The Test Mode 1. Set the following configuration: • Door - must be open • Temperature switch - Air Fluff • End of Cycle Signal switch - Louder • Timer - Timed Drying or Sensor Drying selection 2. Turn the Wrinkle Prevent switch from Off to On three times within a five second period. A single beep, a pause, then a single beep will sound to indicate that the test mode is activated. NOTE: If any of these initial conditions are not satisfied, the control will not enter the test mode. Test Mode Functionality When the control is in test mode, every input change of state will result in an audible beep (with the exception of the End of Cycle Signal switch). This includes: • Door switch • Moisture Sensor (short/open Sensor will result in a beep) NOTE: A moistened finger or damp cloth may also be used. • Temperature switch • Wrinkle Prevent switch • Push to Start (PTS) switch (with the door switch closed) • Timer (any cam input change will result in a beep) NOTE: Timer will advance during test. If any of the inputs do not result in a beep, proceed to the corresponding component tests. 6-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
6-2
Activating The Test Mode
1.
Set the following configuration:
Door - must be open
Temperature switch - Air Fluff
End of Cycle Signal switch - Louder
Timer - Timed Drying or Sensor Drying
selection
2.
Turn the Wrinkle Prevent switch from Off
to On three times within a five second
period. A single beep, a pause, then a
single beep will sound to indicate that the
test mode is activated.
NOTE:
If any of these initial conditions
are not satisfied, the control will not enter
the test mode.
•
•
•
•
Test Mode Functionality
When the control is in test mode, every input
change of state will result in an audible beep
(with the exception of the End of Cycle Signal
switch). This includes:
Door switch
Moisture Sensor (short/open Sensor
will result in a beep)
NOTE:
A moistened finger or damp
cloth may also be used.
Temperature switch
Wrinkle Prevent switch
Push to Start (PTS) switch (with the
door switch closed)
Timer (any cam input change will result
in a beep)
NOTE:
Timer will advance during test.
If any of the inputs do not result in a beep, pro-
ceed to the corresponding component tests.
•
•
•
•
•
•