Miele Scout RX3 Operating instructions/Installation instructions - Page 57

Insert the adhesive holder into

Get Miele Scout RX3 PDF manuals and user guides View all Miele Scout RX3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

en-CA  Remove the battery compartment cover.  Insert the 2 batteries supplied. Make sure the polarity is correct.  Close the battery compartment cover. Switching on the robot vacuum cleaner (Fig. 05)  Slide the I / 0 switch on the side of the robot vacuum cleaner to the I position. The rechargeable battery status indicator lights up in the control field. The robot vacuum cleaner will switch to standby after approx. 60 seconds. The robot vacuum cleaner is reactivated by pressing any button on the remote control or one of the sensor controls in the control field. Connecting the base station (Figs. 06-09) Observe the instructions regarding the handling of the base station and the power supply unit found in the "Safety notes and warnings" section at the beginning of these operating instructions.  Place the base station on a level surface against a free wall within easy access of a power socket. Ensure that there is an obstacle-free distance of at least 1.5 m in front and 0.5 m to the right and left of the base station (Fig. 06).  Insert the plug of the supplied power supply unit into the socket at the back of the base station. You can wind excess cable around the cable rewind. Guide the power supply cable through one of the two cable guides (Fig. 07).  Insert the country-specific power adapter into the power supply unit until it audibly engages and then plug it into the selected power socket (Fig. 08). An adhesive holder is included to permanently fix the base station to the floor (Fig. 09).  Insert the adhesive holder into the recess provided on the underside of the base station until the adhesive holder clicks into place.  Remove the blue protective foil from the adhesive strips.  Place the base station in its chosen location and press down firmly on the base station. You can remove the base station at any time; the adhesive holder remains on the floor. If you want to remove the adhesive holder from the floor, pull on the two pulling-off devices. Charging the battery (Fig. 10) The rechargeable battery is supplied not fully charged. Before using for the first time, it must be fully charged while the robot vacuum cleaner is switched on (switch I / 0 to I). The battery can also be charged when the robot vacuum cleaner is switched off (switch I / 0 to 0). In this case, the vacuum cleaner indicators will not react. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
en-CA
57
Remove the battery compartment
cover.
Insert the 2 batteries supplied. Make
sure the polarity is correct.
Close the battery compartment cover.
Switching on the robot vacuum
cleaner (Fig. 05)
Slide the
I
 / 
0
switch on the side of
the robot vacuum cleaner to the
I
position.
The rechargeable battery status
indicator lights up in the control field.
The robot vacuum cleaner will switch to
standby after approx. 60 seconds. The
robot vacuum cleaner is reactivated by
pressing any button on the remote
control or one of the sensor controls in
the control field.
Connecting the base station
(Figs. 06–09)
Observe the instructions regarding the
handling of the base station and the
power supply unit found in the “Safety
notes and warnings” section at the
beginning of these operating
instructions.
Place the base station on a level
surface against a free wall within easy
access of a power socket. Ensure
that there is an obstacle-free distance
of at least 1.5 m in front and 0.5 m to
the right and left of the base
station (Fig. 06).
Insert the plug of the supplied power
supply unit into the socket at the
back of the base station. You can
wind excess cable around the cable
rewind. Guide the power supply cable
through one of the two cable
guides (Fig. 07).
Insert the country-specific power
adapter into the power supply unit
until it audibly engages and then plug
it into the selected power socket (Fig.
08).
An adhesive holder is included to
permanently fix the base station to the
floor (Fig. 09).
Insert the adhesive holder into the
recess provided on the underside of
the base station until the adhesive
holder clicks into place.
Remove the blue protective foil from
the adhesive strips.
Place the base station in its chosen
location and press down firmly on the
base station.
You can remove the base station at
any time; the adhesive holder remains
on the floor.
If you want to remove the adhesive
holder from the floor, pull on the two
pulling-off devices.
Charging the battery (Fig. 10)
The rechargeable battery is supplied
not fully charged. Before using for the
first time, it must be fully charged while
the robot vacuum cleaner is switched
on (switch
I
 / 
0
to
I
).
The battery can also be charged when
the robot vacuum cleaner is switched
off (switch
I
 / 
0
to
0
). In this case, the
vacuum cleaner indicators will not
react.