Miele Scout RX3 Operating instructions/Installation instructions - Page 77

cleaner does not return

Page 77 highlights

en-CA Problem Possible cause and solution The robot vacuum cleaner switches itself off after it has been switched on using the Power button. The rechargeable battery is not sufficiently charged.  Connect the robot vacuum cleaner correctly to the charging contacts on the connected base station. The robot vacuum cleaner does not return to the base station after vacuuming. It had started vacuuming from somewhere in the room.  The robot vacuum cleaner will return to its starting point. There is insufficient light for the robot vacuum cleaner to navigate.  Provide sufficient lighting. The base station is not connected correctly.  Connect the base station exactly as described in these operating instructions; see "Connection" - "Connecting the base station". The signal between the infrared transmitter on the base station and the robot vacuum cleaner is broken.  Clean the front of the base station and the front of the robot vacuum cleaner carefully with a soft, dry cloth and make sure that no items disrupt the signal. Obstacles on the floor which is to be vacuumed can impede navigation.  Watch the robot vacuum cleaner during vacuuming.  Remove any problematic obstacles.  Section off the problematic area with the magnetic strip.  Reduce the robot vacuum cleaner's maximum crossing over height, see section "Use" - "Reducing the maximum crossing over height". The robot vacuum cleaner is not charging. The base station is not connected correctly.  Connect the base station exactly as described in these operating instructions; see "Connection" - "Connecting the base station". 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132

en-CA
77
Problem
Possible cause and solution
The robot vacuum
cleaner switches itself
off after it has been
switched on using the
Power button.
The rechargeable battery is not sufficiently charged.
Connect the robot vacuum cleaner correctly to the
charging contacts on the connected base station.
The robot vacuum
cleaner does not return
to the base station after
vacuuming.
It had started vacuuming from somewhere in the
room.
The robot vacuum cleaner will return to its starting
point.
There is insufficient light for the robot vacuum
cleaner to navigate.
Provide sufficient lighting.
The base station is not connected correctly.
Connect the base station exactly as described in
these operating instructions; see “Connection” –
“Connecting the base station”.
The signal between the infrared transmitter on the
base station and the robot vacuum cleaner is broken.
Clean the front of the base station and the front of
the robot vacuum cleaner carefully with a soft, dry
cloth and make sure that no items disrupt the
signal.
Obstacles on the floor which is to be vacuumed can
impede navigation.
Watch the robot vacuum cleaner during
vacuuming.
Remove any problematic obstacles.
Section off the problematic area with the magnetic
strip.
Reduce the robot vacuum cleaner’s maximum
crossing over height, see section “Use” –
“Reducing the maximum crossing over height”.
The robot vacuum
cleaner is not charging.
The base station is not connected correctly.
Connect the base station exactly as described in
these operating instructions; see “Connection” –
“Connecting the base station”.