Miele Scout RX3 Operating instructions/Installation instructions - Page 59

Option 2 control field

Page 59 highlights

en-CA Adhesive strips are supplied for permanent fixing. Additional magnetic strips are available to order from the Miele webshop. Starting vacuuming There are 2 ways to start vacuuming: Option 1 (remote control) Use Always observe the robot vacuum cleaner during the first cleaning session in a new environment and after making changes in your home. Remove any problematic obstacles or section off the relevant areas with the magnetic strip or using the controller on a mobile device (see "Connection - Defining the area to be vacuumed"). Check whether steps and drops in height are recognized properly. Your robot vacuum cleaner is equipped with an integrated Wi-Fi module. You can view status information or execute control commands using a mobile device (tablet PC or smartphone). If you would like to control the robot vacuum cleaner using a mobile device, please read "Miele@home". Operation of the robot vacuum cleaner via remote control and the control field is described later in this section. Switching on and off  Press the  button. Option 2 (control field)  Press the  sensor control. The area to be vacuumed will be cleaned. The robot vacuum cleaner always cleans for at least 5 minutes, regardless of the size of the surface to be vacuumed. Finishing vacuuming if vacuuming started from the base station The robot vacuum cleaner will return to the base station and recharge. If the battery is low, the robot vacuum cleaner will return to the base station and recharge. II will appear in the display. The robot vacuum cleaner will then carry on vacuuming.  Press the Power button on the remote control or any sensor control in the control field. Finishing vacuuming if vacuuming started from somewhere in the room The robot vacuum cleaner will return to its starting point and switch to standby after approx. 60 seconds. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132

en-CA
59
Adhesive strips are supplied for
permanent fixing. Additional magnetic
strips are available to order from the
Miele webshop.
Use
Always observe the robot vacuum
cleaner during the first cleaning
session in a new environment and
after making changes in your home.
Remove any problematic obstacles
or section off the relevant areas with
the magnetic strip or using the
controller on a mobile device (see
“Connection – Defining the area to
be vacuumed”). Check whether
steps and drops in height are
recognized properly.
Your robot vacuum cleaner is equipped
with an integrated Wi-Fi module. You
can view status information or execute
control commands using a mobile
device (tablet PC or smartphone).
If you would like to control the robot
vacuum cleaner using a mobile device,
please read “Miele@home”.
Operation of the robot vacuum cleaner
via remote control and the control field
is described later in this section.
Switching on and off
Press the
Power
 button on the
remote control or any sensor control
in the control field.
Starting vacuuming
There are 2 ways to start vacuuming:
Option 1 (remote control)
Press the

 button.
Option 2 (control field)
Press the

 sensor control.
The area to be vacuumed will be
cleaned.
The robot vacuum cleaner always
cleans for at least 5 minutes, regardless
of the size of the surface to be
vacuumed.
Finishing vacuuming if vacuuming
started from the base station
The robot vacuum cleaner will return to
the base station and recharge.
If the battery is low, the robot vacuum
cleaner will return to the base station
and recharge.
II
will appear in the
display. The robot vacuum cleaner will
then carry on vacuuming.
Finishing vacuuming if vacuuming
started from somewhere in the room
The robot vacuum cleaner will return to
its starting point and switch to standby
after approx. 60 seconds.