Miele TXI 680 WP Eco and Steam Operating instructions/Installation instruction - Page 45

Preparing the condensed water container for the Steam Care program

Get Miele TXI 680 WP Eco and Steam PDF manuals and user guides View all Miele TXI 680 WP Eco and Steam manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Condensed water container Preparing the condensed water container for the Steam Care program During the Steam Care program, the condensed water collected in the condensed water container is sprayed into the drum via a spray jet. The condensed water container must therefore be filled with water to at least the -min- marker. Otherwise, this could cause a fault. The -min- marker is at the front lefthand side of the container. 1 spout, 2 rubber seal  Pour the water in through the rings of the spout 1. The spray jet in the door opening can suffer a blockage. It should only be filled with clean water. The water must not contain any fragrance, detergent, or other substances. Make use of the condensed water which collects during the drying process. Filling the empty condensed water container  You can fill the condensed water container with commercially available condensed water (ironing water). You should only use tap water in exceptional circumstances. If tap water is used frequently, however, the spray jet (in the door opening) can become calcified. Checking the rubber seal from time to time If tap water is used frequently, white limescale deposits can build up on the rubber seal 2.  Use a damp cloth to carefully remove any limescale deposits from the rubber seal 2. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Condensed water container
45
Preparing the condensed wa-
ter container for the Steam
Care program
During the
Steam Care
program, the
condensed water collected in the con-
densed water container is sprayed into
the drum via a spray jet. The con-
densed water container must therefore
be filled with water to at least the
–min–
marker. Otherwise, this could
cause a fault.
The
–min–
marker is at the front left-
hand side of the container.
Make use of the condensed water
which collects during the drying
process.
Filling the empty condensed water
container
You can fill the condensed water con-
tainer with commercially available
condensed water (ironing water).
You should only use tap water in excep-
tional circumstances. If tap water is
used frequently, however, the spray jet
(in the door opening) can become calci-
fied.
1
spout,
2
rubber seal
Pour the water in through the rings of
the spout
1
.
The spray jet in the door opening can
suffer a blockage.
It should only be filled with clean wa-
ter. The water must not contain any
fragrance, detergent, or other sub-
stances.
Checking the rubber seal from time
to time
If tap water is used frequently, white
limescale deposits can build up on the
rubber seal
2
.
Use a damp cloth to carefully remove
any limescale deposits from the rub-
ber seal
2
.