Miele TXI 680 WP Eco and Steam Operating instructions/Installation instruction - Page 95

RemoteUpdate, Activation, Running a RemoteUpdate

Page 95 highlights

Settings RemoteUpdate The RemoteUpdate function is used for updating the software in your tumble dryer. RemoteUpdate is activated by default. If you do not install a RemoteUpdate, you can continue to use your tumble dryer in the usual way. However, Miele recommends installing RemoteUpdates. Activation The RemoteUpdate menu option is only displayed and can only be selected if you have added your tumble dryer to your WiFi network (see "Settings - Miele@home"). Miele's RemoteUpdate function can only be used if the tumble dryer is connected to a WiFi network and you have an account in the Miele@mobile app. The tumble dryer must be registered in the app. See the Miele@mobile app for terms and conditions of use. Some software updates can only be carried out by Miele Customer Service. Running a RemoteUpdate If a RemoteUpdate is available for your tumble dryer, it will be displayed automatically for you. You can choose to start the RemoteUpdate immediately or wait until later. If you select "Start later", the prompt to run the RemoteUpdate will be displayed again the next time you switch on your tumble dryer. The RemoteUpdate can take a few minutes. Please note the following information about the RemoteUpdate function: - You will only receive a message when a RemoteUpdate is available. - Once a RemoteUpdate has been installed, it cannot be undone. - Do not switch off the tumble dryer during a RemoteUpdate. Otherwise, the RemoteUpdate will be aborted and will not be installed. 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100

Settings
95
RemoteUpdate
The RemoteUpdate function is used for
updating the software in your tumble
dryer.
RemoteUpdate is activated by default.
If you do not install a RemoteUpdate,
you can continue to use your tumble
dryer in the usual way. However, Miele
recommends installing RemoteUpdates.
Activation
The RemoteUpdate menu option is
only displayed and can only be se-
lected if you have added your tumble
dryer to your WiFi network (see “Set-
tings – Miele@home”).
Miele’s RemoteUpdate function can
only be used if the tumble dryer is con-
nected to a WiFi network and you have
an account in the Miele@mobile app.
The tumble dryer must be registered in
the app.
See the Miele@mobile app for terms
and conditions of use.
Some software updates can only be
carried out by Miele Customer Service.
Running a RemoteUpdate
If a RemoteUpdate is available for your
tumble dryer, it will be displayed auto-
matically for you.
You can choose to start the RemoteUp-
date immediately or wait until later. If
you select “Start later”, the prompt to
run the RemoteUpdate will be displayed
again the next time you switch on your
tumble dryer.
The RemoteUpdate can take a few
minutes.
Please note the following information
about the RemoteUpdate function:
-
You will only receive a message when
a RemoteUpdate is available.
-
Once a RemoteUpdate has been in-
stalled, it cannot be undone.
-
Do not switch off the tumble dryer
during a RemoteUpdate. Otherwise,
the RemoteUpdate will be aborted
and will not be installed.