Miele TXI 680 WP Eco and Steam Operating instructions/Installation instruction - Page 58

scribed in Frequently Asked Questions - Replac

Get Miele TXI 680 WP Eco and Steam PDF manuals and user guides View all Miele TXI 680 WP Eco and Steam manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Frequently Asked Questions Message Possible cause and solution  Clean plinth filter. The system has been clogged by lint or detergent See  lights up residue. after a program  To switch off the message: press OK. has been canceled.  Clean the lint filters and the plinth filter. Please see "Cleaning and care" for notes on clean- ing.  Check that the lint filters and the plinth filter are not damaged or worn. If all lint filters are damaged, deformed, or cannot be cleaned anymore, they must be replaced. For information on when to replace a plinth filter that is not functioning properly, refer to "Frequently Asked Questions - Replacing the plinth filter".  Clean plinth filter. The plinth filter looks clean after thorough cleaning. See  continues However, the program terminates and the fault mes- to light up after a sage appears again. It is likely that there is still un- program has derlying residue that could not be removed. been canceled,  To switch off the message: press OK. despite thorough  Check for the possible causes described below. cleaning. The heat exchanger is clogged.  Check the heat exchanger. Follow the instructions described in "Frequently Asked Questions - Checking the heat exchanger". The plinth filter is clogged further down.  Check the plinth filter. Follow the instructions described in "Frequently Asked Questions - Replacing the plinth filter".  If the plinth filter is not deformed or defective, you can reactivate it in the washing machine. Follow the instructions described in "Frequently Asked Questions - Reactivating the plinth filter". 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Frequently Asked Questions
58
Message
Possible cause and solution
Clean plinth filter.
See 
 lights up
after a program
has been can-
celed.
The system has been clogged by lint or detergent
residue.
To switch off the message: press
OK
.
Clean the lint filters and the plinth filter.
Please see “Cleaning and care” for notes on clean-
ing.
Check that the lint filters and the plinth filter are
not damaged or worn.
If all lint filters are damaged, deformed, or cannot be
cleaned anymore, they must be replaced. For infor-
mation on when to replace a plinth filter that is not
functioning properly, refer to “Frequently Asked
Questions – Replacing the plinth filter”.
Clean plinth filter.
See 
 continues
to light up after a
program has
been canceled,
despite thorough
cleaning.
The plinth filter looks clean after thorough cleaning.
However, the program terminates and the fault mes-
sage appears again. It is likely that there is still un-
derlying residue that could not be removed.
To switch off the message: press
OK
.
Check for the possible causes described below.
The heat exchanger is clogged.
Check the heat exchanger. Follow the instructions
described in “Frequently Asked Questions –
Checking the heat exchanger”.
The plinth filter is clogged further down.
Check the plinth filter. Follow the instructions de-
scribed in “Frequently Asked Questions – Replac-
ing the plinth filter”.
If the plinth filter is not deformed or defective, you
can reactivate it in the washing machine. Follow
the instructions described in “Frequently Asked
Questions – Reactivating the plinth filter”.