Miele TXI 680 WP Eco and Steam Operating instructions/Installation instruction - Page 55

Cleaning the plinth filter, instructions provided in Frequently

Get Miele TXI 680 WP Eco and Steam PDF manuals and user guides View all Miele TXI 680 WP Eco and Steam manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Cleaning the plinth filter Cleaning and care  Pull the handle out of the plinth filter.  Clean the plinth filter thoroughly under running water.  Squeeze the plinth filter very carefully several times as you rinse it.  Rinse the plinth filter until all visible residues have been removed.  Use a damp cloth to remove any lint from the handle.  Install the plinth filter back on the handle. Make sure it is the correct way round.  Damage caused by a damaged or worn plinth filter. The heat exchanger will clog up if the plinth filter is not in good working order. This can cause a fault. Check the plinth filter following the instructions provided in "Frequently Asked Questions - Replacing the plinth filter". Replace the plinth filter if necessary.  Push the plinth filter in completely. This will push in the right-hand guide pin at the same time. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Cleaning and care
55
Cleaning the plinth filter
Pull the handle out of the plinth filter.
Clean the plinth filter thoroughly un-
der running water.
Squeeze the plinth filter very carefully
several times as you rinse it.
Rinse the plinth filter until all visible
residues have been removed.
Use a damp cloth to remove any lint
from the handle.
Damage caused by a damaged
or worn plinth filter.
The heat exchanger will clog up if the
plinth filter is not in good working or-
der. This can cause a fault.
Check the plinth filter following the
instructions provided in “Frequently
Asked Questions – Replacing the
plinth filter”. Replace the plinth filter if
necessary.
Install the plinth filter back on the
handle. Make sure it is the correct
way round.
Push the plinth filter in completely.
This will push in the right-hand guide
pin at the same time.