Miele TXI 680 WP Eco and Steam Operating instructions/Installation instruction - Page 56

Cleaning the plinth-filter access panel, Cleaning the dryer, panel

Get Miele TXI 680 WP Eco and Steam PDF manuals and user guides View all Miele TXI 680 WP Eco and Steam manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Cleaning and care Cleaning the plinth-filter access panel Cleaning the dryer Disconnect the tumble dryer from the electrical supply.  Damage due to the use of un- suitable care products. Unsuitable care products could damage plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or all-purpose cleaners.  Use a damp cloth to remove any lint. Make sure that you do not damage the rubber seal when doing this.  Close the heat-exchanger access panel.  Damage or ineffective drying if drying takes place without a plinth filter or when the heat-exchanger access panel is open. An excessive accumulation of lint can damage the tumble dryer. If the system is not leak-tight, this can make the drying ineffective. Only operate the tumble dryer with the plinth filter installed and the heatexchanger access panel closed.  Clean the tumble dryer and the seal on the inside of the door with a slightly damp soft cloth and a mild solution of liquid dish soap and water.  Dry all the parts with a soft cloth. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Cleaning and care
56
Cleaning the plinth-filter access
panel
Use a damp cloth to remove any lint.
Make sure that you do not damage
the rubber seal when doing this.
Close the heat-exchanger access
panel.
Damage or ineffective drying if
drying takes place without a plinth
filter or when the heat-exchanger ac-
cess panel is open.
An excessive accumulation of lint
can damage the tumble dryer. If the
system is not leak-tight, this can
make the drying ineffective.
Only operate the tumble dryer with
the plinth filter installed and the heat-
exchanger access panel closed.
Cleaning the dryer
Disconnect the tumble dryer from the
electrical supply.
Damage due to the use of un-
suitable care products.
Unsuitable care products could dam-
age plastic surfaces and other parts.
Do not use any solvents, abrasive
cleaners, glass cleaners, or all-pur-
pose cleaners.
Clean the tumble dryer and the seal
on the inside of the door with a
slightly damp soft cloth and a mild
solution of liquid dish soap and water.
Dry all the parts with a soft cloth.