Netgear XSM4324FS Hardware Installation Guide - Page 42

•

Gigabit transceiver modules:

-

AGM734

. SFP transceiver 1000BASE-T, SFP copper RJ-45 GBIC

-

AXM765

. SFP+ transceiver 10GBASE-T, SFP+ copper RJ-45 GBIC

Note

: The AXM765 module is supported on switch models M4300-24XF and

M4300-48XF only.

•

Direct attach cables:

-

AXC761

. SFP+ 1m direct attach cable

-

AXC763


-

AXC765


-

AXC767


-

AXC7610


-

AXC7615


-

AXC7620


For more information about NETGEAR SFP and SFP+ transceiver modules and cables,

visit netgear.com/business/products/switches/modules-accessories

. If purchased,

transceiver modules and cables are shipped separately form the switch.

USB port

The switch provides one USB 2.0 port that lets you upgrade firmware from a disk, back

up the configuration to a storage device, and allow for the collection of a memory dump

for debugging purposes.

A device that you attach to the USB port must comply with the following requirements:

•

The USB device must support USB 2.0.

•

The USB device must support the FAT32 or VFAT file type. The NTFS file type is not

supported.

Because of hardware limitations, the write speed to and read speed from a USB device

is about 1 Mbps.

Note:

In a stack, only the switch that functions as the master can detect and manage

an attached USB device.

Hardware Installation Guide

42

Hardware Overview

M4300 Intelligent Edge Series Fully Managed Stackable Switches

Section	Page
Contents	4
1. Introduction	6
Overview	7
Hardware features	8
About stacking	10
Safety instructions and warnings	11
2. Hardware Overview	14
Hardware descriptions, M4300 series full 10G models	15
Front panel, M4300 series full 10G models	15
Back panel, M4300 series full 10G models	19
LEDs, M4300 series full 10G models	21
Hardware descriptions, M4300 series 1G models with 10G uplinks	23
Front panel, M4300 series 1G models with 10G uplinks	23
Back panel, 4300 series 1G models with 10G uplinks	27
LEDs, M4300 series 1G models with 10G uplinks	29
Hardware descriptions, M4300 series full 10G models with RJ45/SFP+ combo ports	31
Front panel, M4300 series full 10G models with RJ45/SFP+ combo ports	31
Back panel, M4300 series full 10G models with RJ45/SFP+ combo ports	35
LEDs, M4300X series full 10G models with RJ45/SFP+ combo ports	38
Switch hardware interfaces	40
Cables and speed	40
RJ-45 ports, including 10GBASE-T RJ-45 ports	40
10GBASE-X, 1000BASE-X, and 1000BASE-T transceiver modules and cables for SFP+ ports	41
USB port	42
Out-of-band 1G Ethernet port	43
Mini USB console port	43
RJ-45 RS232 console port	43
RPS interface	43
Reset button	43
Power supply units	44
PoE power budgets	45
3. Installation	47
Step 1: Prepare the site	48
Step 2: Protect against electrostatic discharge	48
Step 3: Unpack the switch	49
Step 4: Install the switch	51
Install a full-width switch in a rack	51
Install a single half-width switch in a rack	52
Install two half-width switches in a rack	54
Install the switch on a flat surface	56
Optional Step 5: Install SFP transceiver modules	56
Install an SFP transceiver module in a full 10G model	56
Install an SFP transceiver module in an uplink or combo port	57
Optional Step 6: Install a power supply unit	58
Optional Step 7: Connect a redundant power supply to model M4300-52G-POE+	59
Step 8: Check the installation	60
Step 9: Apply AC power and check the LEDs	61
Optional Step 10: Connect a console to the switch	62
4. Maintenance and Troubleshooting	64
Replace a power supply unit	65
Replace a half-width switch in a rack	66
Troubleshooting chart	68

Netgear XSM4324FS Hardware Installation Guide - Page 42

USB port, AGM734, AXM765, AXC761

Page 42 highlights