Home » Netgear Manuals » Hubs & Switches » Netgear XSM4324FS » Manual Viewer

Netgear XSM4324FS Hardware Installation Guide - Page 45

PoE power budgets

Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

M4300 Intelligent Edge Series Fully Managed Stackable Switches Table 5. Supported PSUs (Continued) Switch Model M4300-48X M4300-48XF Possible PSU Configurations 1x APS250W 2x APS250W 1x APS250W 2x APS250W Power Redundancy RPS Support Note: For models M4300-28G-POE+ and M4300-52G-POE+, the switch automatically selects the APS1000W PSU to provide the power and turns off the APS550W PSU. If the APS1000W PSU is removed or fails, the switch uses the APS550W PSU to provide the power and might reboot if the consumed power is more than the power that the APS550W PSU can provide. PoE power budgets The PoE power budgets for models M430-16X, M4300-28G-POE+, and M4300-52G-POE+ differ and depend on the installed PSU or PSUs. The following tables describe the PoE power budgets. Table 6. PSU and PoE budgets for model M4300-16X PSU (Single PSU only) APS299W APS600W PSU Configuration 110 VAC or 220 VAC input 110 VAC or 220 VAC input M4300-16X PoE Power Budget 199W 500W Table 7. PSUs and PoE budgets models M4300-28G-POE+ and M4300-52G-POE+ PSU PSU Configuration (Single or dual PSU) M4300-28G-POE+ M4300-52G-POE+ PoE Power Budget PoE Power Budget Single APS550W 110 VAC or 220 VAC input 480W 480W Dual APS550W 1+1 RPS mode, 110 VAC or 220 VAC input 480W 480W EPS mode, 110 VAC or 220 VAC input 720W 720W Single APS1000W 110 VAC input 630W 591W 220 VAC input 720W 860W Hardware Overview 45 Hardware Installation Guide

Section	Page
Contents	4
1. Introduction	6
Overview	7
Hardware features	8
About stacking	10
Safety instructions and warnings	11
2. Hardware Overview	14
Hardware descriptions, M4300 series full 10G models	15
Front panel, M4300 series full 10G models	15
Back panel, M4300 series full 10G models	19
LEDs, M4300 series full 10G models	21
Hardware descriptions, M4300 series 1G models with 10G uplinks	23
Front panel, M4300 series 1G models with 10G uplinks	23
Back panel, 4300 series 1G models with 10G uplinks	27
LEDs, M4300 series 1G models with 10G uplinks	29
Hardware descriptions, M4300 series full 10G models with RJ45/SFP+ combo ports	31
Front panel, M4300 series full 10G models with RJ45/SFP+ combo ports	31
Back panel, M4300 series full 10G models with RJ45/SFP+ combo ports	35
LEDs, M4300X series full 10G models with RJ45/SFP+ combo ports	38
Switch hardware interfaces	40
Cables and speed	40
RJ-45 ports, including 10GBASE-T RJ-45 ports	40
10GBASE-X, 1000BASE-X, and 1000BASE-T transceiver modules and cables for SFP+ ports	41
USB port	42
Out-of-band 1G Ethernet port	43
Mini USB console port	43
RJ-45 RS232 console port	43
RPS interface	43
Reset button	43
Power supply units	44
PoE power budgets	45
3. Installation	47
Step 1: Prepare the site	48
Step 2: Protect against electrostatic discharge	48
Step 3: Unpack the switch	49
Step 4: Install the switch	51
Install a full-width switch in a rack	51
Install a single half-width switch in a rack	52
Install two half-width switches in a rack	54
Install the switch on a flat surface	56
Optional Step 5: Install SFP transceiver modules	56
Install an SFP transceiver module in a full 10G model	56
Install an SFP transceiver module in an uplink or combo port	57
Optional Step 6: Install a power supply unit	58
Optional Step 7: Connect a redundant power supply to model M4300-52G-POE+	59
Step 8: Check the installation	60
Step 9: Apply AC power and check the LEDs	61
Optional Step 10: Connect a console to the switch	62
4. Maintenance and Troubleshooting	64
Replace a power supply unit	65
Replace a half-width switch in a rack	66
Troubleshooting chart	68