Onkyo TX SR800 Owner Manual - Page 17
Connecting a television monitor or projector MONITOR
UPC - 751398004926
View all Onkyo TX SR800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
Connecting to Audio/Video equipment : Signal flow Video input S Video input 5. TV monitor or projector (MONITOR OUT) S Video input Video input Analog audio input L (white) R (red) 6. VCR (VIDEO 1) R (red) Analog audio output L (white) Video output S Video output DIGITAL INPUT COAX 1 PRE NRNA FRONT AUDIO VIDEO S VIDEO MONITOR OUT 2 3 OPT 1 2 3 DIGITAL OUTPUT OPT SUB AM SURR SURR BACK / R ZONE 2 FM 75 FRONT R IO L SUB PHONO SURR R SURR BACK CD OUT TAPE GND L IN IO OUT R L IN ZONE 2 DVD OUT IN VIDEO 1 OUT IN VIDEO 2 IN VIDEO 3 R L AUDIO IN VIDEO 4 VIDEO S VIDEO COMPONENT VIDEO OUTPUT Y PB PR INPUT 1 Y PB PR INPUT 2 Y PB PR Y CAUTION: SPEAKER IMPEDANCE PB 4 OHMS MIN. O 6 OHMS MIN. / SPEAKER SEE PR INSTRUCTION MANUAL FOR CORRECT SETTINGS. C S Component video input 5. Connecting a television monitor or projector (MONITOR OUT) The TX-SR800 is equipped with a simple Y/C separate circuit and simple Y/C mixed circuit. Since both the signal from the S VIDEO and VIDEO inputs are output to the MONITOR OUT S VIDEO output, if the television or projector is equipped with an S video input, it is unnecessary to connect the video connectors. If it is equipped with only a video input, connect it to the MONITOR OUT VIDEO output. Using an RCA video cable, connect the video input jack (composite) of the device to the MONITOR OUT VIDEO jack of the TX-SR800. Or if the device has an S video input jack, connect it to the MONITOR OUT S VIDEO jack of the TX-SR800 using an S video cable. Or if the device has component video inputs, connect them to the bank of COMPONENT VIDEO OUTPUT jacks on the TXSR800. Note: The OSD menu is output for VIDEO and S VIDEO only. 6. Connecting a video cassette recorder (VIDEO 1) Using RCA video cables, connect the video output jack (composite) of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the TX-SR800 and connect the video input jack of the video cassette recorder to the VIDEO 1 VIDEO OUT jack of the TX-SR800. Or if the video cassette recorder has S video input and output jacks, connect them to the VIDEO 1 S VIDEO IN and OUT jacks of the TX-SR800 using S video cables. Or if the video cassette recorder has component video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the TX-SR800. With the initial settings of the TX-SR800, the VIDEO 1 input source is set for the COMPONENT VIDEO INPUT 2 jacks. If you connect the video cassette recorder to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at Setup Menu → Input Setup → Video Setup → Component Video (see page 48). Using RCA audio cable, connect the audio output jacks of the video cassette recorder to the VIDEO 1 AUDIO IN jacks of the TX-SR800 and connect the audio input jacks of the video cassette recorder to the VIDEO 1 AUDIO OUT jacks of the TX-SR800. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks. If you are connecting a digital output device to the VIDEO 1 jack instead of a VCR, connect it to either the DIGITAL INPUT COAX jack or DIGITAL INPUT OPT jack depending on the type of connector on the device. With the initial settings of the TX-SR800, the VIDEO 1 input source is set for digital input at the COAX 2 jack. If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (see page 46). 17