Onkyo TX SR800 Owner Manual - Page 19
source is set for digital input at the OPT 3 jack.
UPC - 751398004926
View all Onkyo TX SR800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
Connecting to Audio/Video equipment 8. Settop box, video camera (VIDEO 3) : Signal flow S Video output Video output L (white) Analog audio output R (red) Digital audio output (optical) DIGITAL INPUT COAX 1 PRE NRNA AUDIO VIDEO S VIDEO MONITOR OUT 2 3 OPT 1 2 3 DIGITAL OUTPUT OPT SUB AM SURR SURR BACK / R ZONE 2 FM 75 FRONT R O L SUB PHONO SURR R SURR BACK CD OUT TAPE GND L IN O OUT R L IN ZONE 2 DVD OUT IN VIDEO 1 OUT IN VIDEO 2 IN VIDEO 3 R L AUDIO IN VIDEO 4 VIDEO S VIDEO COMPONENT VIDEO OUTPUT Y PB PR INPUT 1 Y PB PR INPUT 2 Y PB PR CAUTION: SPEAKER IMPEDANCE 4 OHMS MIN. O 6 OHMS MIN. / SPEAKER SEE INSTRUCTION MANUAL FOR CORRECT SETTINGS. C SP 9. Satellite tuner or television (VIDEO 4) S Video output L (white) Video output R (red) Analog audio output 8, 9. Connecting a satellite tuner, television, or settop box (VIDEO 3 or 4) Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 3 (or 4) VIDEO IN jack of the TX-SR800. Or if the device has an S video output jack, connect it to the VIDEO 3 (or 4) S VIDEO IN jack of the TX-SR800 using an S video cable. Or if the device has component video outputs, connect them to one of the banks of COMPONENT VIDEO INPUT jacks on the TX-SR800. With the initial settings of the TX-SR800, the VIDEO 3 and 4 input sources are set for the COMPONENT VIDEO INPUT 2 jacks. If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at Setup Menu → Input Setup → Video Setup → Component Video (see page 48). Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 3 (or 4) AUDIO IN jacks of the TX-SR800. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack. If the device has a digital output, connect it to either the DIGITAL INPUT COAX jack or DIGITAL INPUT OPT jack of the TXSR800 depending on the type of connector on the device. With the initial settings of the TX-SR800, the VIDEO 3 input source is set for digital input at the OPT 3 jack. If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (see page 46). With the initial settings of the TX-SR800, the VIDEO 4 input source is not set for digital input. If you are connecting a digital component, these settings must be changed at Setup Menu → Input Setup → Digital Setup (see page 46). 10. Connecting video camera, etc. (VIDEO 5 INPUT) Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 5 VIDEO jack of the TXSR800. Or if the device has an S video output jack, connect it to the VIDEO 5 S VIDEO jack of the TX-SR800 using an S video cable. Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 5 AUDIO jacks of the TX-SR800. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack. If the device has an optical digital output, connect it to the VIDEO 5 DIGITAL jack of the TX-SR800. The VIDEO 5 digital input is fixed to the OPTICAL input on the front panel. S Video output Front panel Digital output (optical) 10. Video camera/ Video game (VIDEO 5 INPUT) VIDEO 5 INPUT DIGITAL S VIDEO VIDEO L AUDIO R TX-SR800 Video output L Analog output R 19