Panasonic AJSPX800P AJSPX800 User Guide - Page 46

Information Item Indication Camera Warning and AWB A ACTIVE Report Area AWB B ACTIVE AWB A OK _._K (related to AWB, ABB AWB B OK _._K and switch settings) AWB BREAK _._K AWB NG COLOR TEMP LOW COLOR TEMP HIGH LEVEL OVER LOW LIGHT TIME OVER AWB PRESET _._K ATW MODE CHECK FILTER AWB A VAR_._K AWB B VAR _._K ABB ACTIVE ABB OK ABB BREAK ABB NG W-SHD ACTIVE W-SHD OK W-SHD BREAK W-SHD NG LVL OVER B-SHD READY B-SHD ACTIVE B-SHD OK B-SHD BREAK B-SHD NG (Switch changeover indication) WHITE: # _._K (Low light warning) (Y GET value) AUTO KNEE: ON/OFF GAIN:__dB SS: 1/____ SS:  1/____ SS: SUPER V FILTER: _ _._K EXTENDER: ON/OFF IRIS: __ F _._ LOW LIGHT ___._% (MARKER indication) User button functions UM: USER MAIN button U1: USER1 button U2: USER2 button Filter position WHITE BAL switch position MKR: A/B/OFF INH S.GAIN __dB/OFF DS.GAIN __/OFF S.IRIS ON/OFF I.OVR ON/OFF S.BLK -__/OFF B.STR ON/OFF AUDIO CH1 AUDIO CH2 REC SW Y GET ON RET SW ATW ON/OFF D.ZOOM ON/OFF NEWS-G ON/OFF SLOT SEL 1 - 4 - A B P T Stored gain indication Gain value 6/12/20 __dB 46 Status AWB being performed on Ch A. AWB being performed on Ch B. AWB successful on Ch A. AWB successful on Ch B. AWB action aborted by user. AWB action failed. The second line indicates the status. Color temperature too low. Color temperature too high. Brightness too high. Brightness too low. Action timed-out. AWB cannot proceed because the AWB switch is positioned at [PRE]. AWB cannot proceed during ATW. Make sure the FILTER control is positioned correctly. AWB cannot proceed because [A] is set to "VAR". AWB cannot proceed because [B] is set to "VAR". ABB being performed. ABB action successful. ABB action aborted by user. ABB action failed. White shading being adjusted. White shading has been adjusted. White shading action aborted by user. White shading adjustment failed due to excessive brightness. Black shading accepted (by holding down the ABB switch during ABB adjustment). Black shading being adjusted. Black shading adjustment successful. Black shading adjustment aborted by user. Black shading adjustment failed. The WHITE BAL switch has been switched. # is replaced with A, B or PRE. When [A] and [B] are set to "VAR", then it is indicated as VAR _._ K. When [B] is assigned ATW, then it is indicated as ATW MODE. AUTO KNEE switch has been switched to ON or OFF. Gain has been switched with the GAIN selector switch or a user button. When the shutter speed has been switched, the shutter speed is indicated. Shutter speed is in SYNCRO SCAN mode. Shutter speed is in SUPER V mode. Filter position and detail have been switched. Lens extender has been turned on or off. Indicated when the iris override correction value is to be changed. Brightness too low. When the Y GET function is being carried out (the output brightness level near the Center marker is being measured for about three seconds: the level is represented as a percentage), the output brightness level near the center marker is indicated as a percentage. Current marker type User buttons disabled. Selected S.GAIN Selected DS.GAIN Whether S.IRIS is ON or OFF. Iris override can be set (the IRIS OVERRIDE setting is ON). Status of SUPER BLACK (ON or OFF). When it is ON, the set value is also indicated. Status of BLACK STRETCH (shade correction for the black level): ON or OFF Input signal to be recorded on Audio Channel 1 has been switched. Input signal to be recorded on Audio Channel 2 has been switched. USER button acts as REC switch (only in MODE CHECK mode). Y GET function ON. USER button acts as RET switch (only in MODE CHECK). ATW being performed. Status of the digital zoom (ON or OFF) Status of News Gamma (ON or OFF) Switch that changes the target card is set. Position of the CC/ND filter. Filter not positioned correctly. WHITE BAL switch positioned at [A]. WHITE BAL switch positioned at [B]. WHITE BAL switch positioned at [PRE]. ATW mode active. When brightness and color are outside operating limits, the indication blinks. Storage gain (DS.GAIN) value (when active) Current gain value.