Panasonic AJSPX800P AJSPX800 User Guide - Page 99

8-4 VF 8-4-1 VF DISPLAY 8-4-2 VF MARKER Items/ Adjustable Data Saved Range Remarks Items/ Adjustable Data Saved Range Remarks DISP NORMAL CONDITION HOLD - CU F E NORMAL: Display status constantly. HOLD: Display status only when the MODE CHECK switch is pressed. TABLE A B - CU F E Select the VF MARKER setting table. First, select table A or B, then set the items below for each table. DISP MODE 1 Set the DISP MODE. CENTER MARK OFF Switch the center mark. 2 Switch the camera's Warning/Message 1 OFF: Do not display center mark. 3 indication. Please refer to [4-7-4 Display 2 1: + (large) - CU F E VF OUT Y Modes and Setting Changes/adjustment Result Messages] for more information. Select the VF output. 3 4 - CU F E 2: Hollow (large) 3: + (small) 4: Hollow (small) NAM Y: Brightness signal SAFETY ZONE OFF Select the frame type for the safety zone. R NAM: Output signal with the highest level 1 OFF: Do not display frame. G B - CU F E VF DTL 0 : 3 : - C U F E5 among R, G, and B signals. R: Rch signal G: Gch signal B: Bch signal Select the VF DTL. Additionally enhance the DTL for the VF signal. 0 setting is the same DTL as the primary scan lines. 2 - CU F E SAFETY AREA 80% : 90% : - C U F E 100% FRAME SIG 4:3 13:9 1: Box 2: Corner frame Set the position of the safety zone. Set the frame marker. Only enabled when REC MODE is set to ZEBRA1 0% DETECT : 70% Set the ZEBRA1 detection level (IRE value). 14:9 - C U F E VISTA 16:9. The VISTA ratio is 16:8.65. 8 : - C U F E 109% ZEBRA2 0% DETECT : 85% : - C U F E 109% Set the ZEBRA2 detection level (IRE value). FRAME MARK ON - C U F E OFF FRAME LVL 0 : 15 Set the frame marker to ON or OFF. Set the level outside the frame marker. 0: Equivalent to signal OFF. 15: Same brightness as center area. This setting, however, is disabled if ZEBRA2 ON SPOT Set the ZEBRA2 to ON, OFF, or SPOT. - CU F E the FRAME SIG is set to VISTA. - C U F E OFF LOW LIGHT LVL OFF 10% 15% 20% 25% 30% - C U F E 35% ECU MENU ON DISP. OFF - CU F E 50M ON INDICATOR OFF - CU F E MARKER/CHAR 50% LVL 60% 70% 80% 90% - C U F E 100% Set the camera incoming light volume at which to display LOW LIGNT. Set the menu display on the VF to ON or OFF when the ECU is connected. Set the 50M recording indication to ON or OFF. Adjust the brightness of markers and characters displayed on the VF. 8-4-3 USER BOX Items/ Adjustable Data Saved Range Remarks USER BOX ON OFF Select whether or not to display the USER BOX. - CU F E USER BOX 1 WIDTH : 13 : - C U F E 100 Set the width of the USER BOX. USER BOX 1 HEIGHT : 13 : - C U F E 121 Set the height of the USER BOX. USER BOX H -50 POS : +00 : - C U F E +50 Set the horizontal position of the USER BOX. USER BOX V -121 POS : +000 : - C U F E +121 Set the vertical position of the USER BOX. The ____ in the Adjustable Range column indicates the preset mode. 99