Panasonic AJSPX800P AJSPX800 User Guide - Page 86

Maintenance

Get Panasonic AJSPX800P - P2 CAMCORDER PDF manuals and user guides View all Panasonic AJSPX800P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

6. Inspection of the clock, time code, and user bits 1 Set the user's bit as required. Please refer to [4-5-1 Setting the User Bits] for the setting procedures. 2 Set the time code. Please refer to [4-5-3 Setting the Time Code] for the setting procedures. 3 Set the TCG switch to [R-RUN]. 4 Press the REC START/STOP button. Check that the counter display number changes as recording progresses. 5 Press the REC START/STOP button again. Check that recording stops and the counter display number stops changing. 6 Set the TCG switch to [F-RUN]. Check that the counter display number changes regardless of recording status. 7 Set the DISPLAY switch to [UB]. Each time the HOLD button is pressed, make sure that the displayed value changes in the following sequence: VTCG  DATE  TIME  No display (time zone)  TCG; and also verify that the displayed value is correct. If DATE, TIME, or time zone is not correct, refer to [4-5-2 Setting the Internal Clock's Date and Time] for guidance on setting the correct values. Note that date and time data set for DATE, TIME, and time zone is recorded in clips, and affects the playback sequence, etc. at the time of thumbnail manipulations. 7-2 Maintenance 7-2-1 Cleaning Inside the Viewfinder z Do not use thinner or other solvents to remove dirt from the viewfinder. z Wipe the lens with a commercially available lens cleaner. z DO NOT wipe the mirror. If dirt or rubbish is sticking on the mirror, remove it with a commercially available air blower. 7-2-2 Phenomenon Inherent to CCD Cameras Smears Smears may appear when shooting an object with very high brightness. This phenomenon may appear more frequently as the electronic shutter speed increases. 7-2-3 Replacing the Backup Battery The camera is shipped from the factory with a backup battery already mounted. When the battery runs out, the [BACK UP BATT EMPTY] display appears on the viewfinder screen for 3 seconds after the power switch is turned ON. The internal clock stops operating when the battery runs out. Also, the TCG time code value returns to [00:00:00:00], and the time code backup is disabled. The battery must be replaced. Please consult your nearest service center for replacement with a new battery (CR2032). The backup battery is visible when the panel on the LCD monitor side is removed (right side when viewed from the front). Please contact the store where you purchased the camera or an authorised service provider when replacing the battery. 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
86
6. Inspection of the clock, time code, and user bits
1
Set the user’s bit as required.
Please refer to [4-5-1 Setting the User Bits] for the setting
procedures.
2
Set the time code.
Please refer to [4-5-3 Setting the Time Code] for the setting
procedures.
3
Set the TCG switch to [R-RUN].
4
Press the REC START/STOP button.
Check that the counter display number changes as
recording progresses.
5
Press the REC START/STOP button again.
Check that recording stops and the counter display number
stops changing.
6
Set the TCG switch to [F-RUN].
Check that the counter display number changes regardless
of recording status.
7
Set the DISPLAY switch to [UB].
Each time the HOLD button is pressed, make sure that the
displayed value changes in the following sequence: VTCG
DATE
TIME
No display (time zone)
TCG; and
also verify that the displayed value is correct.
If DATE, TIME, or time zone is not correct, refer to [4-5-2
Setting the Internal Clock’s Date and Time] for guidance on
setting the correct values.
<Note>
Note that date and time data set for DATE, TIME, and time
zone is recorded in clips, and affects the playback
sequence, etc. at the time of thumbnail manipulations.
7-2
Maintenance
7-2-1
Cleaning Inside the Viewfinder
Do not use thinner or other solvents to remove dirt from the
viewfinder.
Wipe the lens with a commercially available lens cleaner.
DO NOT wipe the mirror. If dirt or rubbish is sticking on the
mirror, remove it with a commercially available air blower.
7-2-2
Phenomenon Inherent to CCD
Cameras
Smears
Smears may appear when shooting an object with very high
brightness.
This phenomenon may appear more frequently as the electronic
shutter speed increases.
7-2-3
Replacing the Backup Battery
The camera is shipped from the factory with a backup battery
already mounted.
When the battery runs out, the [BACK UP BATT EMPTY] display
appears on the viewfinder screen for 3 seconds after the power
switch is turned ON.
The internal clock stops operating when the battery runs out.
Also, the TCG time code value returns to [00:00:00:00], and the
time code backup is disabled. The battery must be replaced.
Please consult your nearest service center for replacement with
a new battery (CR2032).
The backup battery is visible when the panel on the LCD monitor
side is removed (right side when viewed from the front).
<Note>
Please contact the store where you purchased the camera or
an authorised service provider when replacing the battery.